background image

 

 

KE RT Series UPS 6-10kVA UL 208-220-230-240Vac User Guide English 20180130    This manual is for qualified personnel only 

- 26 -

 

5.4.1

 

Mode setting                                       

 

Mode setting – Note: the area marked by the broken-line will be flashing. 

 

Use button ENTER /ON to choose different modes. There are 4 different modes for setting: 
ECO, PAL, NOR, CF.   

 

Press UP & DOWN to exit the mode setting (save the mode setting), and move to output 
voltage setting or parallel redundancy quantity setting.   

 

5.4.2

 

Output voltage setting 

 

Output voltage setting – Note: the area marked by the broken-line will be flashing. 

 
Within the mode setting press DOWN or within the frequency setting press UP, to go to the output 
voltage setting.       

 

Use button ENTER/ON to choose the different output voltage. There are 4 different voltages--
-208,220, 230, 240.   

 

Press ESC/OFF button to exit the output voltage setting (save the output voltage setting) and 
goes to mode setting or frequency setting. 

NOTE:When  powered by inverter, it is  necessary to turn  off  the inverter before setting  voltage and 

frequency level. 

 

Summary of Contents for RT 10KVA





























Reviews: