background image

 

 

KE RT Series UPS 6-10kVA UL 208-220-230-240Vac User Guide English 20180130    This manual is for qualified personnel only 

- 31 -

 

5.4.10

 

Parallel ID setting 

           

 

        Parallel ID setting – Note: the area marked by the broken-line will be flashing. 

 

Within the bypass voltage lower limit setting press DOWN or within parallel quantity setting press 
UP, to go to the parallel ID setting.       

 

Use button ENTER/ON to set the different parallel ID. The parallel ID range is 1~4.   

 

Press ESC/OFF button to exit the parallel ID setting (save the parallel ID setting) and goes to 
bypass lower limit setting or parallel quantity setting. 

NOTE: Parallel cable cannot be connected when setting the parallel parameters. 
 

5.4.11

 

Parallel quantity setting   

 

Parallel quantity setting – Note: the area marked by the broken-line will be flashing. 

 
Within the parallel ID setting press DOWN or within parallel redundancy quantity setting press UP, to 
go to the parallel quantity setting.       

 

Use button ENTER/ON to set the parallel quantity. The parallel quantity range is 2~4.   

 

Press ESC/OFF button to exit the parallel quantity setting (save the parallel quantity setting) 
and goes to parallel ID setting or parallel redundancy quantity setting. 

 

 

 

 

 

Summary of Contents for RT 10KVA





























Reviews: