background image

 

11

 

5.1.  Assign base station name 

 

Each base station should be given a name. The default name is the serial number of the base station. 
The name always appears when connecting and disconnecting the base station with the handheld 
terminal. 
 

Note: 

To be able to perform this configuration, the base station and the handheld terminal must be 

connected. The connection must be established before starting the DeviceConfig tool. 
 

Note

: For the name please use only letters and numbers and no special characters. 

 
First select the base station in the DeviceConfig tool main menu. 
 

 

Illustration: DeviceConfig tool main menu 

 
Then select the dialog for entering the name of the base station. 
 

 

Illustration: Base station submenu 

 
To enter the name, press the keyboard icon next to the name. An on-screen keyboard opens for 
entering the name. The name dialog also indicates the base station to which the handheld terminal is 
connected (paired). Once the name has been entered, the dialog is exited via "Write to basestation". 
This command writes the name to the base station. 
 

Summary of Contents for KeTop Safe Wireless System





























Reviews: