Keba ServoOne Device Help Download

Page: 166 / 493

Parameter /

Setting

Function

Info

1510

SCD_TSIG_
SignalType

Signal shape: Sine/delta

SINUS(0)

Sine wave generator

TRIANGLE(1)

Triangle wave generator

Sweep (2)

Sweep signal (sine wave)

TriSweep (3)

Sweep signal (triangle
wave)

1511

SCD_TSIG_
BreakTime

Break time

Break (ms) before signal
cycle

Break (ms) between
positive and negative
signal cycle segment

1512

SCD_TSIG_
SymVal

Symmetry value for delta
signal

1513

SCD_TSIG_
Freq2

Upper frequency of the
sweep signal (f)

Table 7.38: Parameters of test signal generator for square and sine signal (con-
tinue)

7.8.4.2 PRBS signal

The PRBS signal is suitable for system excitation with high bandwidth using a test

signal. A feedback shift register is used to generate a binary output sequence with

an amplitude that can be set in P 1509 - SCD_TSIG_ PRBSAmp and a "random"

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

166

7 Control

alternating frequency.

Image 7.44: Example of a PRBS signal

Summary of Contents for ServoOne














































































































































































































































































































































































































































































































Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands

Keba ServoOne, Device Help

Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands