Keba ServoOne Device Help Download

Page: 447 / 493

11.6.45.11 Error 49-10 (emergency code 6100h)

Cause: Alarm on safety controller SR2 of Slave 4 detected

Suggested steps:

Read additional information, check safety system or wiring and acknowledge

alarm/error

Extended diagnosis of safety
errors/alarms.

Further information on the error/alarm code
can be found in the "ServoOne functional
Safety Error Description".

An alarm occured at the
safety controller.

Please check the safety program and the
wiring of the safety system.

Please acknowledge the alarm at the safety
master. The safety master acknowledges all
slave alarms and resets the network status to
"RUN".

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

447

11 Alarms & warnings

11.6.45.12 Error 49-11 (emergency code 6100h)

Cause: Alarm on safety controller SR1 of Slave 5 detected

Suggested steps:

Read additional information, check safety system or wiring and acknowledge

alarm/error

Extended diagnosis of safety
errors/alarms.

Further information on the error/alarm code
can be found in the "ServoOne functional
Safety Error Description".

An alarm occured at the
safety controller.

Please check the safety program and the
wiring of the safety system.

Please acknowledge the alarm at the safety
master. The safety master acknowledges all
slave alarms and resets the network status to
"RUN".

Summary of Contents for ServoOne














































































































































































































































































































































































































































































































Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands

Keba ServoOne, Device Help

Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands