Keba ServoOne Device Help Download

Page: 129 / 493

Index Name

Unit Description

471

MOT_Lsig

mH Motor leakage inductance (ASM) / stator

inductance (PSM)

472

MOT_LsigDiff

q-axis stator inductance variation (relative to
MOT_Lsig)

472

Lsig_q@I0

Inductance @ CurrentI0

472

Lsig_q@I1

Inductance @ CurrentI1

472

Lsig_q@I2

Inductance @ CurrentI2

472

Lsig_q@I3

Inductance @ CurrentI3

472

CurrentI0

Current I0 relative to MOT_CNom

472

CurrentI1

Current I1 relative to MOT_CNom

472

CurrentI2

Current I2 relative to MOT_CNom

472

CurrentI3

Current I3 relative to MOT_CNom

Table 7.6: “Advanced torque control - Saturation characteristic” parameters

7.3.6.1.2 K-T characteristic

In the overload range the output-side torque is reduced due to rising losses

(iron/copper losses). This behaviour can be compensated by P 479[0] - MOT_

TorqueSat.

P No.

Index Parameter name

Unit Function

479

MOT_TorqueSat

Motor torque as a function of the current

0 to 4

Torque; interpolation points 0 to 4.

5 to 9

Current; interpolation points 5 to 9.

Table 7.7: “K-T characteristic” parameters

7.3.6.2 Current observer

In the current control circuit, the calculation of voltage setpoints and PWM runtime

appears as dead time. This is the main factor determining the possible performance

of current control. The current observer eliminates this dead time to the greatest

possible extent by predicting current by means of a scanning step. In addition, many

synchronous servomotors exhibit harmonic components in the current control circuit.

The current observer suppresses these harmonic components so that they cannot

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

129

7 Control

be passed on to the current controller. The disadvantage of the current observer is a

possible deviation between actual current and observed current. This can lead to an

overcurrent shutdown if the maximum current of the device or motor is controlled

stepwise.

The current observer is activated by P 433[0] - CON_CCON_ObsMode = TIME.

Adjust the time constant P 434[0] - Tf in the range from 0.062 ms to 0.5 ms. The

higher the time constant, the greater the smoothing effect of the observer – however,

the greater the possible deviations between actual current and observed current. On

the other hand, effects that do not correspond to the model are suppressed for the

control.

Another peripheral condition is that the electrical data of the motor must be well

defined.

Synchronous motors: see Section "Synchronous motor identification (rotary
and linear)" on page 46.

Asynchronous motor: see Section "Asynchronous motor identification" on
page 46.

Motor inductance (if necessary in connection with the saturation characteristic)

should be parameterised slightly too high.

Index Name

Unit Description

433

CON_CCON_ObsMode

Select current observer mode

434

CON_CCON_ObsPara

Current observer parameters

434

Observer time constant

434

1/s

Proportional feedback gain

434

Integral feedback time constant

434

Decoup

Scale decoupling

434

StatFF

Scale static voltage feed-forward

434

DynFF

Scale dynamic voltage feed-forward

434

FilterFF

Filter voltage feed-forward

Table 7.8: “Advanced torque control - Observer” parameters

Summary of Contents for ServoOne














































































































































































































































































































































































































































































































Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands

Keba ServoOne, Device Help

Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands