Keba ServoOne Device Help Download

Page: 325 / 493

Torque- / force limits

Speed- / velocity limits

Position limitation

Power stage (see Section "Power stage" on page 327)

P 745 - MON_RefWindow and P 746[0] - MON_UsrPosWindow indicate the status

of the configured limits and are incorporated into the general P 151[0] - MPRO_

DRVCOM_STAT_DWord status word.

P 737[0] - MON_MNCTL and P 737[1] - MON_MNSTAT can be used to monitor and

output the status of the mains connection.

Index Name

Unit

Description

338

CON_SCON_ActMax

Motor control limits

338

Max_Speed_Motor

rpm

Maximum motor speed

338

Max_Current_Motor

Maximum motor current

338

Max_Torque_Motor

Maximum motor torque

338

Max_UsrSpeed_Motor

rev/min

Maximum motor speed in user units

338

MaxCurrent_Inverter

Maximum current @ actual voltage level and
switching freq.

338

Reserved

338

Reserved

338

MaxCurrent_Limit

Maximum current limit (motor or inverter)

737

MON_MNCTL

Monitoring control and status word

737

MON_MNCTL

Monitoring control word

737

MON_MNSTAT

Monitoring status word

745

MON_RefWindow

Speed Setpoint reached window

745

TargetReached

rpm

Window for speed control target reached

745

Standstill

rpm

Window for motor standstill

745

TorqueTargetReached

Window for torque target reached

745

Hyst. TargetReached

rpm

Hysteresis window for speed control target
reached

745

Hyst. Standstill

rpm

Hysteresis window for speed control
standstill

746

MON_UsrPosWindow

mDegree Setpoint reached pos. window

Table 10.1: “Limits / thresholds” parameters

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

325

10 Limitations / Thresholds

10.2 Torque- / force limits

The torque is limited to a maximum by

P 329[0] - CON_SCON_TMax

. In the

default setting the torque limit corresponds to the rated torque of the motor.
The possible setting range is 0-1000 %. The parameter can be changed
during operation.

In addition,

P 329[0] - CON_SCON_TMax

can be used to determine what the

maximum current is. To do this, multiply

P 329[0] - CON_SCON_TMax

by the

rated current.

P 332[0] - CON_SCON_TMaxScale

enables the torque limit set in

P 329[0]

to be scaled online – that is, during operation.

It is additionally possible via

P 330[0] - CON_SCON_TMaxNeg

and

P 331[0]

- CON_SCON_TMaxPos

to change the torque limit for different directions of

rotation during operation.

Index Name

Unit Description

329

CON_SCON_TMax

Speed control maximum torque

330

CON_SCON_TMaxNeg

Scaling of negative motor torque limit

331

CON_SCON_TMaxPos

Scaling of positive motor torque limit

332

CON_SCON_TMaxScale %

Scaling of motor torque limit

741

MON_TorqueThresh

Monitoring torque / force threshold

Table 10.2: “Limits / thresholds - Torque / force limits” parameters

NOTE

When using homing methods -8, -9, -10, and -11,

P 332[0] -

CON_SCON_TMaxScale

is replaced by

P 225[0] - MPRO_REF_

HOMING_TMaxScale

To protect against overspeed if a requested torque is not reached,

P 337[0] - CON_SCON_SMaxScale

is used to limit the speed

controller to a percentage of the rated speed.

Summary of Contents for ServoOne














































































































































































































































































































































































































































































































Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands

Keba ServoOne, Device Help

Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands