background image

CONTENTS

 

 

       Page

General Safety............................................................................................................................

Inspection..................................................................................................................................

Handling, Placement and Installation...........................................................................................

Vibration Isolation....................................................................................................................... 

Ventilation..................................................................................................................................

Electrical Information..................................................................................................................

Refrigerant Piping.......................................................................................................................

System Accessories....................................................................................................................

Leak Testing...............................................................................................................................

Evacuation and Dehydration.........................................................................................................

Line Insulation.............................................................................................................................

Refrigerant Charging....................................................................................................................

Compressor Oils..........................................................................................................................

System Start-Up Checklist............................................................................................................

Pressure Controls........................................................................................................................

Low Temperature Room Pull-Down...............................................................................................

Checking Superheat.....................................................................................................................

System Operational Checklist.......................................................................................................

System Troubleshooting..............................................................................................................

Customer Instructions.................................................................................................................

Maintenance Program.................................................................................................................

Service Parts Availability.............................................................................................................

Equipment Start-Up Information...................................................................................................

Product Support Resources.........................................................................................................

“As Built” Service Parts List.........................................................................................................

Parallel Compressor Systems 

Installation and Maintenance

Manual

Air, Water and Remote Models

Hermetic, Semi-Hermetic and 

Scroll Compressors

!

WARNING:

 Only a qualified refrigeration mechanic who is familiar with refrigeration systems and 

components, including all controls, should perform the installation and start-up of the system.

Bulletin K90-KPCS-IM-2     

Part # 

1090001

PRODUCT SUPPORT

web:

 k-rp.com/support

see inside back cover for details

scan:

2

2

3 - 4

4

5

5

6 - 7

8

8

9

10

10

11 - 12

13 - 14

14

14

15

16

17 - 19

20

20

20

22

23

BACK

18/04/22

Summary of Contents for Parallel

























Reviews: