background image

7  -  8            

TIP

CONSUMER INFORMATION

The vehicle identifi-

cation number or 

the engine serial 

number  are used to 

register the vehi-

cle,they are also to 

assist your dealer in 

terms of ordering 

parts or referring to 

s p e c i a l   s e r v i c e  

information  

Meter & Indicator

 engine serial number

  The vehicle identifi-

cation number 

① 

is 

stamped on the right 

side steering head 

tube. 

● 

The engine serial 

number 

② 

is stamped 

on the lower left of the 

crankcase.

Vehicle identification number

( VIN )

*LBBXEHAD9EBB26219*

     

1

VIN No.

ENGINE No.

1.  

Gear Indicator Lamp

Numbers on the meter indicate the 

gear position of the vehicle.  

2.  

Neutral Indicator Lamp

When the transmission is shifted to neutral 

position, the  indicator is on.

3.  

High Beam Indicator Lamp

When the high beam lamp of the headlamp turns on, 

the high beam indicator lamp would be on.

4.  

Tachometer

It indicates the revolving speed of the engine.

5.  

Speedometer

Speedometer shows the running speed.

6.  

Odometer & trip meter:

Relative mileage (TRIP): it records the mileage the vehi

-

cle covers in a period of time.

Odometer (TOTAL): it records the total mileage the vehi

-

cle has covered in km.

7.   

Adjust button

                                         Short press the button to 

switch between km/h and mph.Long press the button to 

reset the "Trip" mileage.

8.   

Fuel Level Indicator

It indicates the fuel level in the fuel tank.

9.   

Turning Indicator

The lamps would flash with the turning signals.

10.  

Clock 

It shows the time. 

11.  

Select button  

Short press the button to switch between trip and odom-

eter functions on the meter.

Press button “SELECT” for several seconds, there will 

appear the interface for time adjustment:

“SELECT” for selection of digits of time display and 

“ADJUST” for adjustment of each value. 

1

7

2
3
4

11

8
9

10

5

6

INSTRUMENT AND CONTROL 

FUNCTIONS

Key Switch

The Steering Lock

“      ”

Off

position: 

All the circuits are off.

 

“      ”

On

 position: 

The circuits are on.

It is set at the lower right 

side of the head tube.

When using it, steer the 

handle to the left, and insert 

the ignition key into the 

steering lock and turn it 

clockwise. 

Do not turn your key to lock the vehicle while 

driving which is not necessary and is also apt to 

cause accident.

Press the key in a proper force.

NOTICE

QJ157FMI-B 

 *41067014*

2

Summary of Contents for 2015 RKS 125-26
















Reviews: