3. 无线中继模式
（通过kisslink无线连接已有路由器，扩大WiFi覆盖范围。）
配置步骤：
i. 接通电源线。此时指示灯环为橙色，表示正在开机中；待指示灯环变成湖蓝色后，表示kisslink完成启动，开始正
常运行。
ii. 将kisslink放置在第一台路由器无线信号能够覆盖的范围内。为了达到理想的上网速度，建议放置在使用手机至少
能搜索到第一台路由器两格信号的范围内。
iii.
将手机打开WiFi选择页面并靠近认证面板。
iv.
听到“beep”声响后，选择KSLINK****网络（不带密码）。
连接成功后会弹出配置页面（如果没有弹出请用浏览器
打开任意一个 网页并访问任意网址如www.abc.com）。在弹出的页面中选择主路由的网络信号名称，并输入密码
v. 等待5-30秒的连接时长。待页面显示连接成功，即可享受畅快的网络体验。
4. 静态IP模式
（kisslink通过配置静态IP实现网络连接。）
配置步骤：
i. 接通电源线。此时指示灯环为橙色，表示正在开机中；待指示灯环变成湖蓝色后，表示kisslink完成启动，开始正
常运行。
ii. 连接网线：将网线一端连接主路由的下行LAN口，另一端连接kisslink的网线接口。
iii. 将手机靠近kisslink认证面板。
iv. 选择KSLINK****网络。连接成功后会弹出配置页面（如果没有弹出请用浏览器打开任意一个网页）。在弹出的配
置页面中输入IP地址、子网掩码、网关地址、DNS服务地址等信息。如果弹出的页面没有配置静态IP选项，请选择
更多上网方式后，再选择静态IP配置。
v. 等待5-30秒的连接时长。待页面显示连接成功后，即可享受畅快的网络体验。
① 认证面板：位于kisslink顶部，中部为kisslink感应探头，周围配有LED呼吸灯环。请参考第二页kisslink外形与部件介绍。
c. Range Extender Setup
This mode requires an existing WiFi network. It’s best utilized as a guest network and/or a way to extend the
current WiFi coverage. Please follow the steps below:
1. Connect kisslink to a power outlet via the included micro-USB cable in an area where there is adequate WiFi signal
from the existing network.
2. Wait for kisslink to start up. The LED indicator will turn from orange to blue when kisslink is ready. Open the WiFi
selection page on any mobile device and hold it close to the syncing panel for authentication. A *beep* will indicate
that the device has been authenticated.
3. Select and join the open KSLINK network on the device. A notification or popup should appear. If not, please open
up a browser and hit refresh to reach the setup page. Select the existing WiFi network and enter the password.
4. A countdown will begin. The process should be complete in less than 30 seconds.
5. Success!
d. Repeater Setup
For a complete WiFi solution, multiple kisslink routers can be linked together to form a seamless WiFi network.
Please follow the steps below:
1. Ensure a mobile device is approved and connected to the existing kisslink network.
2. Connect the additional kisslink(s) to a power outlet via the included micro-USB cable in an area where the
existing kisslink signal is adequate.
3. Open the WiFi selection page on the connected mobile device and hold it close to the syncing panel on the new
kisslink(s) for authentication. A *beep* will indicate that the device has been recognized. Please do not select to join
the new KSLINK network.
4. Wait 2-4 minutes for the new kisslink(s) to sync with the existing kisslink network. The SSID will automatically
reflect that of the existing network.
5. Success!
4
4
