background image

Operation

10

Note:

  

If you manually override either the grade or 

speed setting for the current segment, when that 
segment ends, the TrekMill will automatically adjust 
to the grade and speed settings for the next 
segment.  Because each program is based on a 
preset distance, if you manually increase the speed, 
the time remaining in the current  segment and the 
time remaining in the program will decrease; if you 
manually decrease the speed, the time remaining in 

the current segment and the time remaining in the 
program will increase.

5.

 

Temporarily stopping the program.

To stop the program temporarily, press the Stop 
button once.  When the stop button is pressed and 
the grade is less than 10%, the grade remains 
constant in the stopped position.  When the stop 
button is pressed and the grade is greater than 10%, 
the grade will automatically adjust to 0%.  If you 
press the start button after you have paused the 
program will continue from the point where you 

paused.  If you press the stop button a second time 
the preset program will end and you will have to 
start your program over.

6.

 

Continuing exercise.

If you complete a course, the next course will flash.  
Press the start button to begin the next program.

7.

 Switching to the manual mode.

Press the stop button twice if you want to switch to the 
manual mode.

8.

 

Completing exercise.

When the program is completed step onto the foot rails 
and remove the key from the console.  Make sure to   
keep the key in a secure place.  

Note:

  The displays and indicators on the console will 

remain lit when the power is on even if the key is 
removed.

HOW  TO USE ADMINISTRATOR MODE

When you are finished using the TrekMill, move the on/off switch to the off position and unplug the
power cord.

1.

 Display the Cumulative Distance.

1. Stop the machine.
2. Take the key from the console.
3. Press the middle button and the stop button
at the same time.
4. You can see the cumulative distance in the
distance window.

2.

 Setting the limit of incline and speed.

1. Stop the machine.
2. Take the key from the machine.
3. Press the middle button pressing the stop button at
the same time.
4. Press the middle button once more. 
(Entering the setting mode, max. incline
an max. speed will display).
5. Using the buttons related to the incline
and speed, you can set the limits of incline
and speed.
6. Operate the TrekMill once, prior to powering
off to enable the set values.
7. If you want to cancel this operation turn
the power off without running machine. 

To finish this mode press the stop key.

To finish this mode press the stop key.

Summary of Contents for TrekMill MM5050















Reviews: