background image

 

Page 14 

 

 

DOC0945 (22 August 2022 15:28) 

www.keit.co.uk 

Back to Table of Contents 

3.3.1.  Use at high temperature 

 

Figure 12: Probe is heated causing the spectrum to tilt  

In  Figure  12,  the  spectrum  is  tilted,  with  positive  absorbance  at  lower  wavenumbers  and 
negative  absorbance  at  high  wavenumbers  and  the  spectrum  is  not  flat  in  the  region  800-
1800cm

-1

. This indicates that the probe tip is at a higher temperature now than it was when 

the  background  was  taken.  This  may  cause  chemometric  models  to  give  incorrect  results 
unless the model uses an appropriate pre-treatment to remove the effect. Any model built by 
Keit will have this taken into account. 

3.3.2.  Emitter ageing 

 

Figure 13: Spectrum is tilted showing signs of emitter ageing 

The infrared emitter in the probe is expected to age over its lifetime. The results of this can be 
seen in Figure 13: the spectrum is tilted; the absorbance is positive across the whole spectrum; 
and  the  spectrum  is  not  flat  in  the  region  800-1800  cm

-1

  (contrast  with  Figure  7,  above).  If 

evidence  of  emitter  ageing  is  seen,  it  may  be  required  to  take  a  new  background  scan  to 
remove this effect 

– contact Keit for advice. 

Summary of Contents for IRmadillo ASM0627-09-Z-Cx-O-G-D2x












































Reviews: