Keithley Instruments, Inc.
Cleveland, Ohio 44139
DRN.
CKD.
APP.
DATE
DATE
DATE
PART NUMBER
LTR
REVISIONS
APP. DATE
FORM 28777A-SBG
BRUNING 40-21 62198-SBG
SPECIFICATIONS
HW 1/17/05
Rev B
Page 2 of 2
SPEC-6221
A Released
29843
SZ 6/11/04
B 40096E
Revised
SZ 1/17/05
HW 6/11/04
SK 6/11/04
6221 AC and DC Current Source
ARBITRARY FUNCTION GENERATOR
WAVEFORMS:
Sine, Square, Ramp, and 4 User Defined Arbitrary
Waveforms.
FREQUENCY ACCURACY
4
:
±
100 ppm (1 Year)
AMPLITUDE:
2pA to 210mA peak-peak into loads up to 10
12
Ω
.
AMPLITUDE ACCURACY (<10kHz):
2
Magnitude:
1% rdg + 0.2% rng
Offset:
0.2% rdg + 0.2% rng
SINE WAVE CHARACTERISTICS:
Frequency Range:
1mHz to 100kHz.
2
Amplitude Flatness:
Less than 1dB up to 100kHz.
4
SQUARE WAVE CHARACTERISTICS:
Frequency Range:
1mHz to 100kHz.
2
Overshoot:
<2.5%
4
Variable Duty Cycle:
1,3
Settable to 1
μ
s min. pulse duration,
0.01% programming resolution.
Jitter (RMS):
100ns + 0.1% of period.
4
RAMP WAVE CHARACTERISTICS:
Frequency Range:
1mHz to 100kHz.
2
Linearity:
<0.1% of peak output up to 10kHz.
4
ARBITRARY WAVE CHARACTERISTICS:
Frequency Range:
1mHz to 100kHz.
2
Waveform Length:
2 to 64K points.
Amplitude Resolution:
16 bits (including sign).
5
Sample Rate:
10 MSPS.
5
Jitter (RMS):
100ns + 0.1% of period.
4
Maximum User Waveforms:
4.
PROGRAMMING TIME (Typical):
6
Waveform/Amplitude/Frequency Change:
1ms
ARB Transfer Times:
(External transfer time over Bus)
16K
64K
LAN
0.750s 3.000s
GPIB
1.250s 5.000s
(Internal transfer time of preloaded Arb locations 1-4)
Arb 1
0.001s 0.001s
Arb 2-4
0.500s 2.000s
6221 – 2182 MEASUREMENT FUNCTIONS
DUT RESISTANCE:
Up to 1G
Ω
(1 nSiemen).
(100M
Ω
limit for pulse mode)
DELTA MODE RESISTANCE MEASUREMENTS and
DIFFERENTIAL CONDUCTANCE:
Controls Keithley Model
2182A Nanovoltmeter at up to 24Hz reversal rate (2182 at up to
12Hz).
PULSE MEASUREMENTS:
Pulse widths 50
μ
s to 12ms, 1pA to 100mA.
Repetition interval 83.3ms to 5s.
Waveform Notes:
1. Minimum realizable duty cycle is limited by current range response and load
impedance.
2. Amplitude accuracy is applicable for 100mA through 2
μ
A ranges (Fast
Mode) into a maximum resistive load of 2V/I
fullscale of range
. Amplitude
attenuation will occur at higher frequencies dependent upon current range and
load impedance.
3. For frequencies less than 1 Hz, duty cycle not tested, guaranteed by design.
4. These Specifications are only valid for the 20mA range and a 50
Ω
load.
5. These characteristics for informational purposes only.
6. Typical values are non-warranted, apply at 23
°
C, represent the 50
th
percentile,
and are provided solely as useful information.
GENERAL SPECIFICATIONS
COMMON MODE VOLTAGE:
250Vrms, DC to 60Hz.
COMMON MODE ISOLATION:
>10
9
Ω
, <2nF.
SOURCE OUTPUT MODES:
Fixed DC level, Memory
List, Arbitrary Waveform Function.
REMOTE INTERFACE
Ethernet:
RJ-45 connector, TCP/IP (Auto sensed 10bT or
100bTx), IEEE-488, and RS-232C.
SCPI (Standard Commands for Programmable Instruments)
DDC (command language compatible with Keithley Model
220)
IP CONFIGURATION:
Static or DHCP.
PASSWORD PROTECTION:
11 characters.
DIGITAL INTERFACE:
Handler Interface:
Start of test, end of test, 3 category
bits, +5V@300mA supply.
Digital I/O:
1 trigger input, 4 TTL/Relay Drive outputs
(33V@500mA, diode clamped).
OUTPUT CONNECTIONS:
•
Teflon insulated 3-lug triax connector for output.
•
Banana Safety Jack for GUARD, OUTPUT LO
•
Screw Terminal for CHASSIS
•
DB-9 connector for EXTERNAL TRIGGER
INPUT, OUTPUT, and DIGITAL I/O
•
Two position Screw Terminal for INTERLOCK
INTERLOCK:
Maximum 10
Ω
external circuit impedance.
POWER SUPPLY:
100V to 240V rms, 50-60Hz.
POWER CONSUMPTION:
120VA.
WARRANTY:
1 Year.
ENVIRONMENT:
For Indoor Use Only:
Maximum 2000m above Sea Level.
Operating:
0
°
-50
°
C, 70%R.H. up to 35
°
C. Derate 3%
R.H./
°
C, 35
°
-50
°
C.
Storage:
-25
°
C to 65
°
C, guaranteed by design.
EMC:
Conforms to European Union Directive 89/336/EEC,
EN 61326-1.
SAFETY:
Conforms to European Union Directive
73/23/EEC, EN61010-1.
VIBRATION:
MIL-PRF-28800F Class 3, Random.
WARMUP:
1 hour to rated accuracies.
Passive Cooling:
No fan.
DIMENSIONS:
Rack Mounting:
89mm high x 213mm wide x 370mm
deep (3.5 in. x 8.375 in. x 14.563 in.).
Bench Configuration (with handle and feet):
104mm
high x 238mm wide x 370mm deep (4.125 in. x 9.375 in. x
14.563 in.).
SHIPPING WEIGHT:
4.75kg (10 lbs).
ACCESSORIES SUPPLIED:
Model 237-ALG-2 Triaxial
Test Lead (6.6ft), Trigger Link cable, RS-232 (Null
Modem) cable, Interlock terminal block, User’s Manual,
CD Manual, LabVIEW Drivers.
Summary of Contents for 6220 DC
