Command Reference B-7
Note that parameters for a given source function and range may be sent in
any order; however, once one :CAL:PROT:SOUR command executes, the
other three must also be executed, or an error number -200, "Execution error"
will occur when the :CAL:PROT:SAVE command is processed at the end of
the calibration procedure.
Because the source is calibrated for both positive and negative values, two
zero calibration points are required. The Model 2420 automatically uses the
appropriate zero parameter based on whether the source polarity is positive or
negative.
Example
:CAL:PROT:SOUR 2
Calibrate 2V source range.
Table B-3
Recommended:CALibration:PROTected:SOURce parameter ranges
Note: Actual allowable parameter ranges are ±50% of full range for zero parameters, 75% of full scale to 150% of full
scale for full-range parameters, but ranges listed above should be observed for optimum calibration.
Source
range
First parameter
(negative full scale)
Second parameter
(negative zero)
Third parameter
(positive full scale)
Fourth parameter
(positive zero)
0.2V
-0.18 to -0.22
-0.002 to +0.002
+0.18 to +0.22
-0.002 to +0.002
2V
-1.8 to -2.2
-0.02 to +0.02
+1.8 to +2.2
-0.02 to +0.02
20V
-18 to -22
-0.2 to +0.2
+18 to +22
-0.2 to +0.2
60V
-50 to -65
-0.5 to +0.5
+50 to +65
-0.5 to +0.5
10
µ
A
-9E-6 to -11E-6
-1E-7 to +1E-7
+9E-6 to +11E-6
-1E-7 to +1E-7
100
µ
A
-90E-6 to -110E-6
-1E-6 to +1E-6
+90E-6 to +110E-6
-1E-6 to +1E-6
1mA
-0.9E-3 to -1.1E-3
-1E-5 to +1E-5
+0.9E-3 to +1.1E-3
-1E-5 to +1E-5
10mA
-9E-3 to -11E-3
-1E-4 to +1E-4
+9E-3 to +11E-3
-1E-4 to +1E-4
100mA
-90E-3 to -110E-3
-1E-3 to +1E-3
+90E-3 to +110E-3
-1E-3 to +1E-3
1A
-0.9 to -1.1
-1E-2 to +1E-2
+0.9 to +1.1
-1E-2 to +1E-2
3A
-2.7 to -3.15
-3E-2 to +3E-2
+2.7 to +3.15
-3E-2 to +3E-2
Summary of Contents for SourceMeter 3A 2420
