Models 2510 and 2510-AT
Calibration
2-9
Step 2: Voltage calibration
1.
From the CAL EXECUTE menu, select VOLTAGE, then press ENTER. The instru-
ment will display the following message:
VOLTAGE CAL
Connect only a DMM to Peltier.
©
ß
Then press ENTER.
2.
Connect the DMM to the Model 2510 OUTPUT terminals, as shown in Figure 2-1.
Table 2-4
Calibration step summary
Function*
Calibration step
Test connections
VOLTAGE
8.5V
Output 0V
Output -8.5V
DMM to OUTPUT terminals (Figure 2-1)
DMM to OUTPUT terminals (Figure 2-1)
DMM to OUTPUT terminals (Figure 2-1)
CURRENT
1
Ω
resistor
1
Ω
resistor to OUTPUT terminals (Figure 2-2)
I-PROTECTION
1
Ω
resistor
1
Ω
resistor to OUTPUT terminals (Figure 2-2)
TEMPERATURE
THERMISTOR
RTD
I-SS
V-SS
100
Ω
resistor, short
1k
Ω
resistor, short
10k
Ω
resistor, short
100k
Ω
resistor, short
100
Ω
resistor, short
1k¾ resistor, short
1k
Ω
resistor
1k
Ω
resistor, short
100
Ω
resistor then short to INPUT terminals (Figure 2-3 and Figure 2-4)
1k
Ω
resistor then short to INPUT terminals (Figure 2-3 and Figure 2-4)
10k
Ω
resistor then short to INPUT terminals (Figure 2-3 and Figure 2-4)
100k
Ω
resistor then short to INPUT terminals (Figure 2-3 and
100
Ω
resistor then short to INPUT terminals (Figure 2-3 and Figure 2-4)
1k¾ resistor then short to INPUT terminals (Figure 2-3 and Figure 2-4)
DMM and 1k
Ω
resistor to INPUT terminals (Figure 2-5)
DMM, 1k
Ω
resistor; short to INPUT terminals (Figure 2-4 and Figure 2-5)
AC-OHMS
100
Ω
resistor
100
Ω
resistor to OUTPUT terminals (Figure 2-6)
V-SOURCE
Open leads
None (open OUTPUT terminals)
* CAL EXECUTE menu selections.
WARNING:
NO INTERNAL OPERATOR SERVICABLE PARTS,SERVICE BY QUALIFIED PERSONNEL ONLY.
CAUTION:
FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,REPLACE FUSE WITH SAME TYPE AND RATING.
120
Model 2510
OUTPUT F-
LINE RATING
100-240VAC
50, 60 HZ
90VA MAX
LINE FUSE
SLOWBLOW
2.5A, 250V
!
!
CAT
I
OUTPUT S-
OUTPUT F+
OUTPUT S+
NEXT
PREV
POWER
DISPLAY
2002
MULTIMETER
DCV
ACV
DCI
ACI
Ω
2
Ω
4
FREQ
TEMP
REL
TRIG
INFO
LOCAL
EXIT
ENTER
RANGE
RANGE
!
F
R
500V
PEAK
FRONT/REAR
2A 250V
AMPS
CAL
STORE
RECALL
CHAN
SCAN
FILTER
MATH
CONFIG
MENU
HI
INPUT
LO
SENSE
Ω
4 WIRE
INPUTS
350V
PEAK
1100V
PEAK
AUTO
Model 2002 DMM
INPUT HI
INPUT LO
IEEE-488
(ENTER IEEE ADDRESS
WITH FRONT PANEL MENU)
MADE IN
U.S.A.
ENABLE-DIG I/O
RS-232
TRIGGER
LINK
OUTPUT
F+ S+ S- F-
F+ F- S+ S-
ISOLATION FROM EARTH: 30V MAX.
INPUT
Figure 2-1
Voltage calibration
connections
2510-902-01 (E - Mar 2010)(Service).book Page 9 Tuesday, March 16, 2010 1:04 PM
Summary of Contents for TEC SourceMeter 2510
