background image

Operation

1. 

Turn on the water isolation valve.

2. 

Turn on the electricity supply.

3. 

Check the Control Hub for power. (The LEDs inside the Hub should be illuminated). 

4. 

The Kelda Showers system operates by detecting water flow. It starts when water flow is detected and stops when 
the water flow ceases.

5. 

Open the shower mixer/valve. Water should start to flow from the shower head, followed very quickly by the air flow. 
Once the water valve times out, the water will cease to flow and the air will continue to operate briefly. This purges 
water from the shower head.

Congratulations, you’re now ready to experience the greenest shower in the world and start saving water and 

energy costs!

Troubleshooting

Symptom

Likely cause

Action/Remedy

System does not operate fully 

(reduced or no water flow):

Hot or cold water supply isolation valve 

closed

Check and open valve

Debris has caused blockage in mixer

Isolate mixer and service strainers and 

cartridge see mixer instructions to service

Pressure difference between hot and 

cold supplies is too high 

Adjust screws on mixer to balance. Or fit 

pressure reducer on high pressure supply.

Shower mixer/valve not functioning.

Check valve, replace if necessary.

Water flows from shower head

but no air:

Does the fan run?

if so check seal of air hose connections 

and that hose is kink free.

Is the LED on the front of the Control 

Hub illuminated?

 

If no check electricity supply

Conduct hard reset by switching off 

electrical supply and waiting 10 seconds 

before turning on.

Debris in fan

Clear any debris from fan and follow Fan 

Test Function p.12.
If fan runs then check flow sensor is not 

jammed or faulty.

Temperature fluctuating:

Thermostatic control/Boiler issue.

Check thermostatic mixer valve/boiler for 

an issue, call a specialist if necessary.

Poor/no water flow:

Blocked water filter/strainer.

Isolate water supply and service strainers 

in mixer or group mixer.

Water flow too strong:

Flow restrictor not installed.

Check if the flow restrictor is properly 

installed (in the back of the head).

13

Summary of Contents for 24016



















Reviews: