background image

25/02/2021

Ver. 1

17

Commissioning Procedure

Installed correctly  the  burner  should  not  emit  any 
fumes into the room. The following procedure  should be  
undertaken   to   test   that  the  unit  is  operating correctly.
1

After unit has been operating for a short  period a 

smoke match, smoke tube, carbon dioxide analyser or
similar should be directed  at the  top  opening of the 
unit.

2

This procedure  should be undertaken with the 

following conditions in the room:

• Open or closed windows
• Operation  of extraction/exhaust  fans, range hoods 

etc.

• Operation  of other  gas appliances
• Operation  of optional appliance fan at any speed.

3

Should any spillage be detected  the cause must be

rectified before allowing commissioning of unit.

4.   Please test appliance operation before leaving.

User Instructions

1. WARNING NOTE: 

Properly installed and 

operated this appliance will not leak gases. 
Persistent fume emission must not be tolerated.
If fume emission does exist, then the following 
immediate action should be taken.

A Open doors and windows to ventilate room.
B   Turn the fire off.
C   Check for flue blockage and clear if necessary.
D   Do not attempt to relight the burner until the cause

of the emission has been identified and rectified.
Should assistance be required contact nearest 
agent.

E   The gas burner  is designed to work in a Kemlan

Horizon electronic power flue ignition system.
Working correctly there will be no spillage. Unit
should cut out if not enough draw to ensure proper
functioning.

2

Initially the Kemlan coal fire may burn with a 

slightly blue flame. After approximately 20 minutes
the fire will settle down and burn with a yellow 
flame.

3

As with all gas fires your gas coal/pebble or log 

fire should  be  regularly serviced. We  
recommend  once each year. Service information

for an authorised person to follow has been set
out in attached leaflet.

4

PLEASE   NOTE: Only logs provided by Kemlan

should be used with this appliance.

5

DO NOT place articles on or against this 

appliance.

DO  NOT  use or  store  flammable materials 
near this appliance.
DO  NOT  spray  aerosols  in  the  vicinity of  this 
appliance whilst it is in operation.
DO NOT modify this appliance.
Primarily a decorative  appliance not  certified as 
a space heater.

6

The appliance is a live fuel effect product  

designed to operate with luminous flames and 
may exhibit slight carbon deposition.

7.

The guard is fitted to this appliance to reduce the

risk of fire or injury from burns and no part of it 
should be permanently removed.

SERVICE  - WARNING: ONLY TO  BE SERVICED  
BY AN AUTHORISED PERSON

Installation Instructions Kemlan Three Sided Natural Draft 

Electronic Ignition Gas Fireplaces

Summary of Contents for 1100 Low Line
























Reviews: