104988
– 104988N
DT Istr (104988-104988N) 08/15
– Rev 13_11/2020
9/40
5. The cylinder should be placed as far as possible from the unit without pulling the tubing.
6. The hose must be attached to the stove and to the regulator, in countries in which connection is permitted
by the user, by GAS-COMPATIBLE CLOSED MESH METAL CLAMPS.
7. Ensure that the hose is not to subjected to twisting by placing the gas cylinder in a suitable position with
respect to the stove.
8. THE HOSE MUST ALWAYS BE REPLACED WHEN IT PRESENTS ABRASIONS OR BURNS.
9. Place the stove on the ground or on the floor, always in a horizontal position. Never place the stove on
surfaces made of wood, plastic or other inflammable materials.
10. DO NOT TRY TO OPERATE THE STOVE WITH METHANE.
11. WARNING: to avoid a dangerous overheating of the gas pipe, DO NOT install the hose by passing it under
or behind the stove but at the side, keeping it away from the cooking area (see figure).
CONNECTION AND CHANGE CYLINDER
The gas cylinder should not be dropped or handled carelessly! When the unit is not in use, the cylinder must be
disconnected. Cylinders must be stored outdoors in a vertical position and out of the reach of children. Never
place the cylinder in places where the temperature may exceed 50 °C. Do not place cylinders near open flames
or other sources of ignition.
DO NOT SMOKE NEAR THE CYLINDER.
WARNING:
the cylinder must be changed outdoors and away from any flame or heat source.
For the installation of the cylinder proceed as follows:
1. Close the cylinder valve (4).
2. Check that the valve is closed the stove.
3.
Ensure that there is a seal on the pressure regulator and that it is in
perfect conditions before attaching the regulator on the new gas
cylinder.
4. Attach the regulator (1) to the cylinder.
MOD. 104988
– 104988N
5. Insert the rubber tube on the one hand on the receiver cooker (2) and the other on the pressure regulator
and secure with hose clamps (3).
MOD. 104988D
– 104988ND
5. Screw the crimped tube on one side to the threaded connection of the burner and on the other side on the
pressure regulator.
LEAKAGE TEST
BEFORE USING CHECK THAT THERE ARE NO LEAKS.
Never use an open flame to check for leaks, always use a solution of soap and water or our
article 1726 Revel
Gas.
Check that the control knobs on the grill is closed (OFF). Turn the tap on the gas bottle. Apply solution of
soap and water or ns. Article 1726 Revel gas in the tube and on all connections. If bubbles appear, it means
that there is a loss and it repaired before use. After making the repair, repeat the test. After conducting the test,
close the gas supply to the tank. If it is a leak is detected and you cannot fix it, do not try to fix it another way,
but instead use the Service.
In the case of gas leaks immediately close the valve of the gas cylinder.
FUNCTIONING
1. Check all the connections before using the appliance.
2. Never work with the rubber hose not securely fastened by means of the above-mentioned metal clamps (3).
3. Do not use the appliance if it is leaking, deteriorated or malfunctioning.
4. Place the stove on a stable, horizontal, heating resistant and not flammable surface.
5. Place the stove at a safe distance from inflammable materials and from objects that are sensitive to heat.
6. Ensure that all the taps of the stove are CLOSED (clockwise rotation).
7. Open completely the tap of gas cylinder.
8. Press and turn clockwise to the maximum position of the tap turning on the burner you intend to.
9. At the same time, approach the ignition flame to the burner you want to turn.
10. Make sure the burner is lit.
11. If the flame is extinguished for any reason (blast of wind or spilled liquids) immediately close the taps of the
burner and the cylinder valve. Check the cause of the shutdown and restart if there are no problems with
the ignition process.
12. Place the pot upon the burner support, checking that it is in a stable position and the equipment is properly
balanced.
13. Ensure that the flame does not come out at the bottom of the pot large size.
14. Ensure that liquids do not come out off the pot and extinguish the flame.
15. Do not move the stove with working flame.
16. Warning: the body of the stove (base) may become hot during use. Handle exclusively using gloves.
