background image

Pro 3200 Evolution, Pro 4200 Evolution, Pro 5200 Evolution/0109 – 15

© 

COPYRIGHT

 

KEMPPI

 

OY

9.2.  TERMS OF GUARANTEE

KEMPPI OY provides a guarantee for products manufactured and sold by them if defects in 

manufacture and materials occur.Guarantee repairs must be carried out only by an Authorized 

KEMPPI Service Agent. Packing, freight and insurance costs to be paid by third party. The 

guarantee is effected on the day of purchase. Verbal promises which do not comply with the 

terms of guarantee are not binding on guarantor.

Limitations on guarantee

The following conditions are not covered under terms of guarantee: defects due to natural 

wear and tear, non-compliance with operating and maintenance instructions, connection to 

incorrect or faulty supply voltage (including voltage surges outside equipment spec.), incorrect 

gas pressure, overloading, transport or storage damage, fire or damage due to natural causes 

i.e. ligthning or flooding.
This guarantee does not cover direct or indirect travelling costs, daily allowances or accomoda-

tion.
Note: Under the terms of the guarantee, welding torches and their consumables, feed, drive 

rollers and feeder guide tubes are not covered. Direct or indirect damage due to a defective 

product is not covered under the guarantee. The guarantee is void if changes are made to the 

product without approval of the manufacturer, or if repairs are carried out using non-approved 

spare parts.
The guarantee is also void if repairs are carried out by non-authorised agents.

Guarantee period

The guarantee is valid for one year from date of purchase, provided that the machine is used 

for single-shift operation.
The guarantee period for double and treble shift operation is six months and four months 

respectively.

Undertaking guarantee repairs

Guarantee defects must be informed to KEMPPI or authorised KEMPPI Service Agents within 

the guarantee period. Before any guarantee work is undertaken, the customer must provide proof 

of purchase and serial number of the equipment in order to validate the guarantee.
The parts replaced under the terms of guarantee remain the property of KEMPPI.
Following the guarantee repair, the guarantee of the machine or equipment, repaired or replaced, 

will be continued to the end of the original guarantee period.

Summary of Contents for Pro 3200 EVOLUTION

















Reviews: