background image

Kendrion Kuhnke Automation GmbH 

Construction and Functionality 

 

Vico MT

 (

E 863 GB

) 

28

 

01/10/2021 

 

4 Installation and Operation 

 

WARNING 

Consider the standards and regulations applicable in the country of use 

Improper installation may cause death and serious personal or property damage. 

Consider all standards and regulations applicable in the country of use and only have trained 
experts knowing all the formalities install the unit in machines or systems. 

 

 

Information 

Before installing, servicing or putting the unit into operation, please also read the safety 
information in the preface of this document. 

 

4.1  Mechanical Installation 

Vico MT is a modern electronic assembly. Handle – specifically mount, operate and service – with care. 

Whereas touch screens are generally very tough, you should still take account of a couple of basic facts 
when installing them. 

Check that the front of the housing is always flat and that the material is not warped, irrespective of which 
material is used. Do not expose the front panel to any mechanical pressure (bending stress). 

 Mounting Position 

By design, the unit may be installed vertically only. Not installing it according to instructions may prevent heat 
dissipation and therefore cause it to overheat, which may then provoke a loss in performance or cause the 
unit to switch off unexpectedly. 

Take particular care not to place the unit on a table top or the floor to operate it. 

 

 

CAUTION 

Risk of overheating and fire! 

Even if operated at admissible ambient temperature, the unit may be destroyed if the way of 
installation stops the convection cooling from working. 

  Please take heed of the notes on the mounting position. 

 

Leave some free space above, beneath, at the sides and back of the unit to allow enough air to circulate. Be 
sure to leave at least 50 mm of free space on all sides. This specification applies to all variants. 

 

 

Summary of Contents for Vico MT 1027























































Reviews: