background image

7

Setting the  

Temperature Control

Cool Down Period

• 

For safe food storage, allow four hours for 

the freezer to cool down completely. The 

freezer will run continuously for the first 

several hours. Foods that are already fro

-

zen may be placed in the freezer after the 

first few hours of operation. Unfrozen foods 

should 

NOT

 be loaded into the freezer until 

the freezer has operated for four hours.

• 

When loading the freezer, freeze only 

three pounds of fresh food per cubic foot 

of freezer space at one time. Distribute 

packages to be frozen evenly throughout 

the freezer. It is not necessary to turn the 

control knob to a colder setting while 

freezing food.

Temperature Control 

(may vary by model)

The temperature control is located on the 

front exterior wall. The temperature is 

factory preset to a position which should 

provide a satisfactory food storage tem

-

perature during normal operating conditions. 

However, the temperature control is adjust

-

able to provide a range of temperatures for 

your personal satisfaction.
If a colder temperature is desired, turn the 

temperature control knob toward 

MAX

Adjust 

the temperature gradually, in small increments, 

and allow the temperature to stabilize. For 

warmer temperatures, adjust the knob toward

 

MIN

.

 Allow several hours for temperatures to 

stabilize between adjustments.

MIN

MAX

OFF

IMPORTANT

Setting the temperature control to the OFF 

position turns the cooling system off, but 

the power light will still glow.

NOTE

Your freezer may have some or all of 
the optional features described below. 
Become familiar with these features and 
their use and care.

Power On Light

The green Power On indicator light indicates 

that the freezer is properly connected to 

electrical power. The light glows even when 

the temperature control is turned to OFF. If 

the light goes out, refer to FREEZER DOES 

NOT RUN Section in the Troubleshooting 

Guide. If the freezer appears to be 

operating, the light element may be burned 

out. To schedule light element replacement, 

in the U.S.A. call 1-844-553-6667, and in 

Canada call 1-800-469-4663.

Optional Features

Defrost Drain

The defrost drain provides a method of 

draining the water during defrosting and 

cleaning. See “Defrosting” in 

Care & 

Cleaning

 section.

Summary of Contents for 17602 Series













Reviews: