39
CONNECTING THE WATER LINE
BEFORE YOU BEGIN
This water line installation is not covered by the refrigerator
warranty. Follow these instructions carefully to minimize the
risk of expensive water damage.
Water hammer (water banging in the pipes) in house
plumbing can cause damage to refrigerator parts and can
lead to water leakage or
floo
ding. Call a quali
fied
plumber
to correct water hammer before installing the water supply
line to the refrigerator.
CAUTION:
To prevent burns and product damage, only
connect the refrigerator water line to a cold water supply.
If you use your refrigerator before connecting the water
line, make sure the icemaker is turned OFF at the control
panel.
CAUTION:
Do not install the icemaker tubing in areas
where temperatures fall below freezing.
WATER PRESSURE
A cold water supply.
The water pressure must be between
20 and 120 psi. If the refrigerator is installed in an area
with low water pressure (below 20 psi), you can install a
booster pump to compensate for the low pressure.
If a
reverse osmosis water filtration system
is connected
to your cold water supply, this water line installation is not
covered by the refrigerator warranty. Follow the following
instructions carefully to minimize the risk of expensive water
damage.
If a
reverse osmosis water filtration system
is connected
to your cold water supply, the water pressure to the
reverse osmosis system needs to be a minimum of 40 to
60 psi (276-414 kPa or 2.8-4.2 kgf/cm², less than 2.0-3.0
sec. to fill a cup of 7 oz or 198 cc capacity).
If the water pressure from the reverse osmosis system is less
than 20 psi or 138 kPa or 1.4 kgf/cm² (takes more than 4.0
sec to fill a cup of 7 oz or 198 cc capacity):
Check to see if the sediment filter in the reverse osmosis
•
system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to
•
refill after heavy usage.
If the issue concerning water pressure from reverse
•
osmosis remains, call a licensed, qualified plumber.
All installations must be in accordance with local
•
plumbing code requirements.
CAUTION:
Wear eye protection during installation to
prevent injury.
WHAT YOU WILL NEED
Copper Tubing,
•
¼ in. outer
diameter, to connect the refrigerator
to the water supply. Be sure both
ends of the tubing are cut square.
To determine how much tubing you
•
need: measure the distance from the water valve on the
back of the refrigerator to the water supply pipe. Then,
add 8 feet (2.4 m). Be sure there is sufficient extra tubing
(about 8 feet [2.4 m] coiled into 3 turns of about 10 in.
[25 cm] diameter) to allow the refrigerator to move out
from the wall after installation.
Power drill.
•
½ in. or adjustable wrench.
•
Flat blade and Phillips head screwdrivers.
•
Two ¼ in. outer diameter
•
compression nuts and
2 ferrules (sleeves)
to
connect the copper tubing
to the shutoff valve and the
refrigerator water valve.
If your existing copper water
•
line has a flared fitting at the
end, you will need an
adapter
(available at plumbing supply
stores) to connect the water line
to the refrigerator OR you can
cut off the flared fitting with
a tube cutter and then use a
compression fitting.
Shutoff valve to connect
•
to the cold water line.
The
shutoff valve should have a water inlet with a minimum
inside diameter of
5
/
32
in. at the point of connection
to the COLD WATER LINE.
Saddle-type shutoff valves
are included in many water
supply kits. Before purchasing,
make sure a saddle-type
valve complies with your local
plumbing codes.
NOTE:
A Self Piercing Saddle Type Water Valve should
not be used.
WARNING
Electrical Shock Hazard
When using any electrical device (such as a power
drill) during installation, be sure the device is battery
powered, double insulated or grounded in a manner that
will prevent the hazard of electric shock.
Summary of Contents for 795.7259
Page 1: ...795 7259 MFL68680470 Rev 00_082917 ...
Page 35: ...35 WATER FILTER ...
