TM
The
Prime
Mineral RO
Water Purifier is a product of advanced technology, which ensures safe and clean
drinking water. The purifier is easy and convenient to install.
Recommended Site Preparations :
connection not more than 3m away from the point of installation of purifier
Raw water supply with ½ inch nipple not more than 3m away
Drain for rejected water not more than 3m away
Space as per dimensions of the purifier
Wall/plane surface for mounting two screws and holding the machine
The system and installation must comply with state and local laws and regulations
Specific Instructions :
TM
Prime
Mineral RO Water Purifier is a wall mountable purifier. Make sure that it is only mounted on a
wall. Avoid installation on wooden and metallic stands
For optimum performance and minimum inlet pressure required, ensure that the raw water supply tank is
at least 10 ft above the level at which the purifier is installed
It is preferable to install the purifier near a sink so that inlet and reject water lines are easily available
KENT
KENT
n
n
n
n
n
n
n
n
n
Single Phase 220 ± 10 V AC, 50 Hz
Installation Instructions
UV Fail Alarm*
To ensure delivery of purer and healthier water, a micro-processor is installed in the purifier that performs the
following functions: -
UV Stabilization Delay: To ensure that the UV lamp is pre-heated and is working at its optimum level before it
starts disinfecting water, the controller provides a two seconds delay to UV lamp when the purifier is switched
on. During this period, only the UV lamp is switched on and other electrical devices of the purifier are
switched off.
Purification Delay: To ensure that the idle water lying in the internal pipes and in the UV chamber is disinfected
before being passed into the storage tank, the system provides 5 second delay when the purifier is switched
on. During this time, the UV lamp kills all micro-organisms that may be in the water inside UV chamber. After
this delay, all other electrical devices such as booster pump and solenoid valve are switched on to start
normal purification process.
Audible Alarm: The controller also controls the timing of UV Fail Alarm and the Filter Change Alarm.
Computer Controlled Operation*
Automatic Operation
KENT
TM
Prime
Mineral RO Water Purifier has an in-built feature that sounds an audible alarm if the UV lamp
malfunctions. This feature is provided to ensure purity. This UV Fail Alarm will sound as follows:
Two short beeps after every two seconds.
In case such an alarm is audible, kindly switch off the purifier and call the service technician for help. The purifier
will stop its purification process in such a circumstance.
2 Sec.
2 Sec.
2 Sec.
2 Sec.
Filter Change Alarm*
KENT
TM
Prime Mineral RO has an in-built feature that sounds an audible alarm to indicate replacement time for
filters. This alarm will be audible after 700 hrs of use since the last filter change (or since the time of installation).
The Filter Change Alarm will sound as follows:
4 short beeps after every two seconds; for 30 seconds. The alarm will repeat after every 2 hours of use.
In case such an alarm is audible, please call the service technician and request him to change the filters of the
purifier. However, if the filters are not changed within the next 60 hours of operation, the purifier will stop
functioning to ensure purity and hygiene. The following alarm will be audible after 60 Hrs.
A continuous beep for an infinite time.
In case, such an alarm is audible, kindly switch off the purifier and call the service technician to replace the filters.
In such a circumstance, the purifier will not function unless the filters are changed.
2 Hours
30 Sec.
30 Sec.
n
n
n
n
The purifier automatically shuts off when the
The purifier automatically restarts when water
storage tank is full
level drops below the maximum
The purifier does not start when inlet water supply
The purifier does not allow any water rejection in
2
pressure falls below 0.3 kg/cm
absence of electricity / when tank is full
5
* Tested & Certified by TUV-SUD South Asia (P) Ltd.
Installation Procedure
Wall Hanging Diagram
1.
First fix the SS ball valve (marked as no. 4) to the 1/4 inch port of the 3-way connecter (marked as no.
2) as shown in figure 2.
2.
Connect the 3-way connector to the raw water supply (marked as no. 1) as shown in the figure 3. The
3-way connector is fitted in line with the raw water supply.
3.
The other end of the 3-way connector can be connected to a tap (marked as no.3) as shown in figure
4. or can be plugged off if not required.
Step-2
Figure 1.
Figure 2.
Figure 4.
Figure 3.
1
2
3
4
4
2
1
3
Step-1
Slot holes
6
1.
Paste the central drill sticker on wall at (3.6 Feet to 4.0 Feet from the ground) as per your convenience.
2.
Ensure that sticker is pasted straight on the wall, then drill holes as per the space provided on sticker.
3.
Now, insert the puff up with the help of a hammer.
4.
Screw in two 10X50 self-taping screws, 5.4 inches (138 mm) apart horizontally.
5.
Carefully hang the purifier on the wall with the help of wall-mounting slot holes provided on back side
of the purifier.
Note:
If the wall is not straight or the screws are not properly drilled in an even position, it will damage
your purifier.
Note:
Keep the device away from heat or direct sunlight.
