background image

Support

For technical questions about the products please contact our support team by e-mail.
Send an e-mail with your questions and all the important details of your application and used versions to our 
support address.

KENTIX GmbH
Autenbornstrasse 2
55743 Idar-Oberstein 

support@kentix.de

The manual has been prepared with great care. The correctness and completeness of data, pictures and drawings is not 
guaranteed.

Regard to protected brand names and logos:

The use of protected trademarks, trade names, designs and brand logos in this manual is not a copyright violation, but 
serves as an illustrative reference. Even if these are not at the appropriate places marked as such, the relevant statutory 
provisions. The trade names and logos are the property of the manufacturer and subject to copyright laws. Information 
about that, please refer to the instructions of the manufacturers websites.

Copyright Notice:

All rights reserved. Any text, images, graphics, animations and videos as well as content and structure of this manual are 
protected by copyright and other laws protecting intellectual property. Your copy, modification, commercial use, use in 
other media or transfer to third parties is prohibited or requires the prior express permission of such KENTIX GmbH.

Electronic equipment is not domestic waste - in accordance with directive 2002/96/EC OF THE 
EUROPEAN PARLIAMENT AND THE COUNCIL dated 27th January 2003 concerning used electrical 
and electronic appliances, it must be disposed of properly. At the end of its service life, take this unit for 
disposal at a designated public collection point.

Spent batteries are special waste!

Do not throw spent batteries into your domestic waste; take them to a collection point for spent batteries.

The products complies with applicable European standards and directives and is confirmed by the CE 

mark.

The CE conformity declaration is available on request.

Page 15                                          

!

(09-2012, subject to change)

!

www.kentix.de

Summary of Contents for MultiSensor-LAN
















Reviews: