background image

ARHC-1

REV B: 08/13

OPERATING INSTRUCTIONS

                                                       

                         

ONLY TRAINED PERSONNEL ARE TO OPERATE THIS TOOL. 

1.

TO ENSURE TOOL IS OPERATING PROPERLY, PERFORM FOLLOWING STEPS AT START OF EACH SHIFT:

MAKE SURE TOOL MOVES UP AND DOWN FREELY WHILE HANGING FROM BALANCER OVERHEAD.

WITH POWER TO TOOL TURNED ON, TEST TRIGGER FOR PROPER OPERATION.

DEPRESS EACH TRIGGER SEPARATELY.  TOOL SHOULD NOT ACTIVATE.  DEPRESS BOTH TRIGGERS. TOOL 
SHOULD ACTIVATE.

IF TOOL HAS "ANTI-TIE DOWN" OPTION, BOTH TRIGGERS MUST BE DEPRESSED SIMULTANEOUSLY FOR TOOL 
TO ACTIVATE.

2.

TO PERFORM WORK, HOLD TOOL FIRMLY AT BOTH HANDLES.  SQUEEZE TRIGGERS TO ACTIVATE TOOL.

3.

DO NOT EXERT EXCESSIVE PRESSURE. ALLOW TIME FOR THE TOOL TO CUT.

4.

TOOL REQUIRES 40 S.C.F.M. OF AIR @ 90 P.S.I. AIR PRESSURE.

MAINTENANCE

                           ONLY TRAINED AND QUALIFIED PERSONNEL ARE TO PERFORM MAINTENANCE
                           AND SERVICE TO THIS TOOL.

1.

FILL LUBRICATOR WITH KENTMASTER AIR MIST OIL (PART NO. 7903050). SET DRIP RATE ACCORDING TO 
INSTRUCTIONS SUPPLIED.

2.

TOOL REQUIRES GREASING AT START OF EVERY SHIFT. GREASE USING KENTMASTER GREASE (PART NO. 7903070).

3.

FLUSH AIR MOTOR AT END OF EACH DAY’S USE BY SQUIRTING A FEW SQUIRTS OF KENTMASTER AIR OIL MIST (PART 
NO. 7903050) DIRECTLY INTO THE AIR INLET PORT. RUN TOOL A FEW SECONDS TO COAT AND PROTECT THE AIR 
MOTOR AND INTERNAL PARTS OF TOOL.

BLADE REMOVAL AND CLEANING

 

 

.

  

                                   ALWAYS DISCONNECT POWER SUPPLY FROM TOOL BEFORE INSTALLING OR
                                   REMOVING BLADE FROM TOOL.

                             ALWAYS WEAR WIRE MESH GLOVES WHEN INSTALLING OR REMOVING BLADE FROM TOOL.

1.

TO REMOVE BLADE, LOOSEN SCREW, FIGURE 1, ITEM 1 .

2.

REMOVE BLADE , ITEM 4 .

3.

CLEAN ALL PARTS REMOVED WITH SOAP AND WATER.

4.

REPLACE BLADE WHEN NECESSARY AND LUBRICATE ALL PARTS.

5.

REASSEMBLE ALL PARTS IN REVERSE ORDER.

AT END OF EACH SHIFT:

1.  

REMOVE BLADE.

2.

  IF USING BLADE AGAIN, WASH BLADE WITH HOT WATER TO REMOVE FAT, MEAT AND BONE PARTICLES.

3.

  DRY AND APPLY A COAT OF MINERAL OIL TO ENTIRE SURFACE OF BLADE TO AVOID OXIDATION.

KENTMASTER MFG. CO., INC.

 

1801 SOUTH MOUNTAIN AVE., MONROVIA, CALIFORNIA   91016

 

UNITED STATES OF AMERICA

 TELEPHONE: (626) 359-8888   FAX: (626) 303-5151

3 OF 13

   

!

   WARNING

   

!

   WARNING

   

!

   WARNING

   

!

   WARNING

Summary of Contents for ARHC-1














Reviews: