31
Registration of Title
Chapter 1
Chapter 2
Chapter 3
Chapter 4
Chapter 5
Chapter 6
Chapter 7
D
D
S
I
C
C
E
R
D
A
N
I
3
G
In regard to disc information reading
The entered title is read in to the disc with the following
timing.
÷
When the disc door is closed.
÷
With closed disc door, when title input mode is finished.
DISPLAY-A : The display flashes.
Do not move or exchange discs until the disc information
has been read in.
When there are discs for which the disc information already has been
read in, there may be no display.
2
Press the SET button.
3
Enter the track title.
To enter the track title
1
Select the track number.
SET
0
D
1
0
T
C
7
0
CHARACTER
4
¢
DOWN
UP
RANDOM
DISPLAY
3
2
4
CONFIRM
REPEAT
1
7
6
8
5
+10
0
+100
9
(
)
A
B
C
D
E
F
G
BEST
SELECTION
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
X
Y
Z
W
/
.
–
SELECTOR
'
DISC
CONTINUOUS
PLAY
SUB OUT
MONITOR
DISPLAY-A
10-key Remote
Keyboard
4
¢
SET
,
<
Q
W
E
R
T
Y
U
I
O
P
A
S
D
F
G
H
J
K
L
:
Z
X
C
V
B
N
M
>
/
?
.
,
,,
,
;
@
2
!
1
#
3
$
4
%
5
^
6
&
7
✱
8
9
0
-
+
=
(
)
÷
One character is set and the cursor goes to the next digit.
÷
Repeat this to enter the track title.
C
A
Z
B
= >
Flashing cursor
4
Store the track title.
ENTER
6
ENTER
Previous
track
Next track
Previous
track
N e x t
track
÷
Up to 20 track titles can be registered per disc by repeating steps from
1
to
4
for each.
To quit TITLE INPUT mode
Press the MODE button.
I
T
L
T
I
E
T
S
R
O
!
E
O
!
M
÷
To register another track titles in the same disc, repeat the entire
procedure of “
To enter the track title
“.
To change the character type
SHIFT
CHARAC.
/P.MODE
C
A
Z
B
= >
c
a
z
b
= >
2
0 1
= >
Capital letters
: ABC.....XYZ.....
1
Small letters
: abc.....xyz.....
2
3
Numbers/symbols
: 0 1 2 3.....7 8 9
space ! " # $ % & ' () * + , - . / : ; < = >
? @ ^ _ ` 0.....
10-key Remote
Keyboard
10-key Remote
Keyboard
÷
The type of characters which can be entered is switched each time the
CHARAC.
button is pressed.
10-key Remote
Main unit
Holding this button down,
press a character or
numeric button.
÷
To input a small (lowercase) letter or a symbol, press and hold
SHIFT
while press the desired character or numeric/symbol button.
÷
If a desired character is not provided on the remote control buttons,
input the character as follows. Press the
CHARACTER (DOWN/UP)
buttons or rotating the
DISC SKIP
knob on the main unit (provided that
the
OPERATION-A
indicator is lit) until the desired character is dis-
played in the flashing cursor position. Then, press the
SET
button.
