adjusting the height of the tools
Please refer to page 9 on how to assemble the mixer.
whisk, stainless steel K beater, stirring tool
For best performance the whisk, K beater and stirring tool should be
almost
touching the bottom of the bowl
. If necessary adjust the height
using the spanner provided.
Here’s how:
1 Unplug the appliance.
2 Raise the mixer head and insert the whisk, beater or stirring tool.
3 Lower the mixer head. If the clearance needs to be adjusted, raise the
mixer head and remove the tool.
4 Using the spanner provided loosen the nut
sufficiently to allow
adjustment of the shaft
. To lower the tool closer to the bottom of the
bowl, turn the shaft anti-clockwise. To raise the tool away from the bottom
of the bowl turn the shaft clockwise.
5 Re-tighten the nut.
6 Fit the tool to the mixer and lower the mixer head. (Check its position see
points above).
7 Repeat the above steps as necessary until the tool is set correctly. Once
this is acheived tighten the nut securely.
high temperature flexible beater
- this tool should just touch the
bottom of the bowl.
dough hook
- this tool is set at the factory and should require no
adjustment.
to fit and use your splashguard
assembly
The splashguard assembly consists of 2 pieces: the heat shield and the
splashguard.
The heat shield must be fitted during cooking operations
otherwise the mixer will not operate and error code E:03 will
be displayed.
The heat shield is to protect the mixer head from steam
produced during the cooking process.
If necessary both the heat shield and the splashguard can be fitted to retain
ingredients in the bowl e.g. when mixing light ingredients such as flour and
icing sugar, or when cooking ingredients where moisture needs to be
retained in the bowl. The splashguard should not be fitted to the bowl
unless used in conjunction with the heat shield.
1 Raise the mixer head until it locks.
2 Push the heat shield upwards onto the underside of the mixer head
until
fully located. The heat shield must never be used without the rubber seal
correctly fitted.
3 Fit the bowl onto the base.
4 Lower the mixer head.
5 Rest the splashguard on the bowl rim and then slide forward until fully
located
.
●
During mixing, ingredients can be added directly to the bowl via the feed
chute.
6 To remove the splashguard simply slide it away from the appliance.
7 To remove the heat shield, raise the mixer head until it locks. Remove the
tool, then pull the heat shield downwards from the underside of the mixer
head.
Note: Only fit or remove the splashguard when the mixer head is in the
locked position.
8
Summary of Contents for Cooking Chef KM070 Series
