4
weighing function
Your food processor is fitted with a built in weighing function to allow
ingredients to be weighed straight into the bowl or liquidiser goblet.
●
The Maximum weighing capacity is 3Kg. This is the total weight of all the
ingredients plus the weight of the bowl or goblet.
to use the weighing function
1 Always fit the detachable drive shaft, bowl and attachment or liquidiser
goblet onto the power unit before adding ingredients.
2 Plug in – the display screen will remain blank.
3 Press the ON/ZERO button once and the display
screen will light up.
4 Press the (kg/lb) button to select either grams or
ounces. The display will default to kg/g when first
switched on.
●
The unit weighs in 2g increments and
teaspoon/tablespoon measures are recommended
for weighing small quantities.
5 Check the display shows ‘0’, if not, zero by
pressing the ON/ZERO button. Then weigh the
required ingredients straight into the bowl or goblet.
After the weight is displayed, press the ON/ZERO
button and the display will return to ‘0’. Add the next ingredients and that
weight will be displayed. Repeat until all ingredients are weighed.
●
If the display is not zeroed and either the ingredients or the
bowl/attachment/lid are removed the display will show [ - - - -] to represent
a minus reading.
To zero press the ON/ZERO button once.
6 Add the lid and select a speed to operate the processor.
●
During operation the display screen with freeze [- - - -] until the speed
control returned to the off position.
●
After processing the last weight will be displayed on the screen when the
speed control is returned to the off position. Note: The weight of the lid will
be included if the display is not zeroed before switching on.
●
The weight of any additional ingredients added down the feed tube whilst
the processor is running will not be shown on the display screen.
'
weighing tray
A removable weighing tray is supplied for
weighing ingredients without the bowl or
liquidiser.
To use, place the tray on top of the power unit.
Then follow steps 2 to 5 under ‘to use the
weighing function’
To remove, just lift the tray off.
auto switch off
●
The display screen will turn off automatically if the same weight reading is
shown after 5 minutes.
●
The display screen can be turned off manually by pressing and holding
down the ON/ZERO button for a few seconds.
important
●
Do not overload by exceeding the maximum weighing capacity of 3Kg. The
display will show [0 – Ld] if the weighing function is overloaded.
●
Do not subject the power unit to excessive force as this may damage the
weighing sensor.
●
Always place the processor on a dry flat surface prior to weighing.
●
Do not move the power unit during operation of the weighing function.
to use your liquidiser
1 Fit the sealing ring
(
into the blade unit
)
- ensuring the seal is located
correctly in the grooved area.
●
Leaking will occur if the seal is damaged or incorrectly fitted.
2 Hold the underside of the blade unit
)
and insert the blades into the goblet
- turn anti-clockwise to lock
.
3 Put your ingredients into the goblet.
4 Fit the lid to the goblet and push down to secure
. Fit the filler cap.
●
Before fitting the liquidiser to the power unit check that the
speed control is in the 0 position and the Auto light is off. If the
speed control is not in the 0 position or the Auto is selected the
liquidiser will operate as soon as the liquidiser is fitted.
5 Place the liquidiser onto the power unit with the handle situated to the right
hand side and turn clockwise to lock
.
●
The appliance will not operate if the liquidiser is incorrectly
fitted to the interlock.
6 Use the Auto button or select a speed (refer to the recommended speed
chart) or use the pulse control.
safety
●
Liquids should be allowed to cool to room temperature before
blending.
●
Always take care when handling the blade assembly and avoid touching the
cutting edge of the blades when cleaning.
●
Only operate the liquidiser with the lid in place.
●
Only use the goblet with the blade assembly supplied.
●
Never run the liquidiser empty.
●
To ensure the long life of your liquidiser, do not run it continuously for longer
than 60 seconds.
●
Smoothie recipes - never blend frozen ingredients that have formed a solid
mass during freezing, break it up before adding to the goblet.
hints
●
When making mayonnaise, put all the ingredients, except the oil, into the
liquidiser. Remove the filler cap. Then, with the appliance running, add the
oil slowly through the hole in the lid.
●
Thick mixtures, e.g. pâtés and dips, may need scraping down. If the mixture is
difficult to process, add more liquid.
●
Ice crushing - operate the pulse in short bursts until crushed to the desired
consistency.
●
The appliance will not work if the liquidiser is incorrectly fitted.
●
To blend dry ingredients - cut into pieces, remove the filler cap, then with
the appliance running, drop the pieces down one by one. Keep your hand
over the opening. For best results empty regularly.
●
Don’t use the liquidiser as a storage container. Keep it empty before and after
use.
●
Never blend more than 1.5 litres (2pts 12floz) - less for frothy liquids like
milkshakes.
multi mill
Use the mill for processing dry ingredients such as nuts, coffee beans and it
is also suitable for processing a range of spices such as: -
Black peppercorns, cardamom seeds, cumin seeds, coriander seeds, fennel
seeds, fresh ginger root, fresh chillies and whole cloves.
to use your multi mill
1 Put your ingredients into the jar. Fill it no more than half full.
2 Fit the sealing ring
to the blade unit
.
3 Hold the underside of the blade unit and insert the blades into the jar – turn
anti-clockwise to lock
.
4 Place the mill onto the power unit and turn clockwise to lock
.
5 Use the Auto button, or select a speed (refer to the recommended speed
chart).
safety
●
Never fit the blade unit to your food processor without the jar fitted.
●
Never unscrew the jar while the mill is fitted to your appliance.
●
Do not touch the sharp blades – Keep the blade unit away from children.
●
Never remove the mill until the blades have completely stopped.
●
To ensure the long life of your mill, do not run it continuously for longer than
60 seconds. Switch off as soon as you have got the right consistency.
●
The appliance will not work if the mill is incorrectly fitted.
●
Do not process turmeric root in the mill as it is too hard and may damage the
blades.
hints
●
For optimum performance when processing spices we recommend that you
do not process more than 100g at a time in the mill.
●
Whole spices retain their flavour for a much longer time than ground spices
so it is best to grind a small quantity fresh at a time to retain the flavour.
●
To release the maximum flavour and essential oils whole spices are best
roasted prior to milling.
●
Cut ginger up into small pieces before processing.
●
For best results the mini bowl attachment is recommended when chopping
herbs.