6
English
English
7
Getting Started
Canceling the display
demonstration
The display demonstration is always turned
on unless you cancel it.
When you turn on the power (or after you
reset the unit), the display shows:
[CANCEL DEMO]
\
[PRESS]
\
[VOLUME
KNOB]
1
Press the volume knob.
[YES]
is selected as the initial setup.
2
Press the volume knob again to confirm.
[DEMO OFF]
appears.
■
■
If no operation is done for about 15 seconds
or if you turn the volume knob to select
[NO]
in step 2,
[DEMO MODE]
appears and
the display demonstration starts.
Setting the demonstration mode
1
Press the volume knob to enter
[FUNCTION]
.
2
Turn the volume knob to select
[DEMO
MODE]
, then press to enter.
3
Turn the volume knob to select
[ON]
or
[OFF]
.
If
[ON]
is selected, display demonstration
starts if no operation is done for about 20
seconds.
4
Hold to finish the procedure.
Adjusting the clock
1
Press the volume knob to enter
[FUNCTION]
mode.
2
Turn the volume knob to select
[SETTINGS]
, then press to enter.
3
Turn the volume knob to select
[CLOCK]
,
then press to enter.
4
Turn the volume knob to select
[CLOCK
ADJUST/ CLOCK ADJ]
, then press to
enter.
Clock hour flashes on the display.
5
Turn the volume knob to adjust the hour,
then press to enter minute adjustment.
Clock minutes flashes on the display.
6
Turn the volume knob to adjust the
minute, then press to confirm.
Press
4
/
¢
to move between the
hour and minute adjustment.
7
Hold to finish the procedure.
Initial settings before operations
1
Press SRC to enter
[STANDBY]
mode.
2
Press the volume knob to enter
[FUNCTION]
mode.
3
Turn the volume knob to select
[INITIAL SET]
, then press to enter.
4
Turn the volume knob to make a selection, then press to confirm.
See table below for selection.
5
Hold to finish the procedure.
Item
Selectable setting (Preset: *)
PRESET TYPE
NORMAL/ NORM
*: Memorizes one station for each preset button in each band (FM1/ FM2/ FM3/ MW/ LW). ;
MIX:
Memorizes one station for each preset button regardless of the selected band (FM1/ FM2/ FM3/ MW/ LW).
KEY BEEP
ON */ OFF:
Activates/deactivates the keypress tone.
RUSSIAN SET
ON:
Folder name, file name, song title, artist name, album name are displayed in Russian (if applicable). ;
OFF *:
Cancels.
P-OFF WAIT
Sets the duration when the unit will automatically turns off (while in standby mode) to save the battery.
––– :
Cancels ;
20M *:
20 minutes ;
40M:
40 minutes ;
60M:
60 minutes
BUILT-IN AUX/
BUILTIN AUX
ON *:
Enables “AUX” in source selection. Sound of the connected external component is produced through the
car speakers. ;
OFF:
Disables “AUX” in source selection.
CD READ
1 *:
Automatically distinguishes between audio file disc and music CD. ;
2:
Forces to play as a music CD. No sound can be heard if an audio file disc is played.
SWITCH PREOUT/
SWITCH PRE
REAR */ SUB-W:
Selects whether rear speakers or a subwoofer are connected to the line out terminals on the
rear of the unit (through an external amplifier).
SP SELECT
OFF */ 5/4/ 6 × 9/6/ OEM:
Selects the speaker size for optimum performance.
F/W UP xx.xx
YES:
Starts upgrading the firmware. ;
NO *:
Cancels (upgrading is not activated).
For details on how to update the firmware, see: www.kenwood.com/cs/ce/
