to assemble the food mincer
1 Fit the food mincer scroll
E
inside the food mincer
body
F
.
2 Fit the cutter
D
– cutting side outermost. Ensure
it is seated properly, otherwise you could damage
your food mincer.
3 Fit a screen
C
. Put the notch over the locating
tab
cn
.
4 Loosely fit the ring nut
B
.
to assemble the pasta maker
Optional: for easier pasta making, warm the parts in
hot water before assembling. Then dry thoroughly
before assembling.
1 Fit the pasta scroll
J
inside the food mincer
body
F
.
2 Fit a screen
K
,
L
,
M
or
N
. Put the notch over
the locating tab
co
.
3 Loosely fit the ring nut
B
.
to fit the attachment to the
machine
1 Raise the mixer head.
2 With the attachment in the position shown, align
the drive tabs on the end of the scroll with the
corresponding slots in the bowl tool socket
cp
.
3 Push the attachment into the socket and turn anti-
clockwise until it locks into place.
4 Hold the feed tube in place and tighten the ring nut
by hand.
5 Fit the tray
cq
.
important
l
Never operate the attachment for longer than 10
minutes as this could damage your mixer.
l
The attachment will not operate unless
the dual speed outlet cover is fitted.
to use your food mincer
l
Thaw frozen food thoroughly before
mincing.
Cut meat into 2.5cm (1”) wide strips.
1 Switch to maximum speed. Using the pusher
I
,
gently push the food through one piece at a time.
Do not push hard
– you could damage your
food mincer.
2 Once all the food has been minced, switch off and
unplug.
3 Remove the food mincer. Use the spanner
A
to
remove the ring nut if it is too tight.
to use the pasta maker
1 Make your pasta dough. –
a too-dry mix could
break your pasta maker.
2 Switch to maximum speed.
3 Place some of the mix onto the hopper. Feed a
small amount of mix into the feed tube at a time.
Allow the scroll to clear before continuing.
If the feed tube becomes clogged use the end
of the spanner handle
A
to push the mix onto
the scroll.
Do not push too hard or use the
mincer pusher – you could damage the
pasta maker.
Never let the feed tube fill up.
4 When the pasta is long enough, cut to the desired
length.
5 Remove the pasta maker. Use the spanner
A
to
remove the ring nut if it is too tight.
l
Cook rigatoni within 4 hours. Otherwise it will
become brittle and snap.
to cook your pasta
1 Bring a pan three quarters full of water to the boil.
Add salt to taste.
2 Add your pasta and gently boil for 3- 8 minutes,
stirring occasionally.
cm
compact chopper/grinder
attachment
A
jar
B
sealing ring
C
blade unit
to use your compact chopper/
grinder
Use the compact chopper/grinder for milling herbs,
nuts and coffee beans.
1
Put the ingredients into the jar
A
.
2
Fit the sealing ring
B
into the blade unit
C
.
l
Leaking will occur if the seal is damaged
or incorrectly fitted.
3
Turn the blade unit upside down. Lower it into the
jar, blades down.
4
Screw the blade unit onto the jar until finger tight
cr
. Refer to the graphics on the underside of the
blade unit as follows:
- unlocked position
- locked position
11
Summary of Contents for KHH30 multizone
