NX-720
9
7. Clone Mode
Programming data can be transferred from one trans-
ceiver to another by connecting them via their modular
microphone jacks. The operation is as follows (the transmit
transceiver is the source and the receive transceiver is a tar-
get). Clone mode should be enabled.
The following data cannot be cloned.
• Tuning data
• Embedded message with password
• Model name data
• ESN (Electronic Serial Number) data
Note:
The following data can be cloned.
• Fleet (own)/ID (own) for FleetSync
• Unit ID (own) for NXDN
• ID (own) for MDC-1200
1. Turn the source transceiver power ON with the [
] key
held down (1 second), “CLONE MODE” is displayed on
the LCD.
2. Power on the target transceiver.
3. Connect the cloning cable (No. E30-3382-05) to the mod-
ular microphone jacks on the source and target.
4. Press the [ ] key on the source transceiver.
The data of the source is sent to the target. While the
source is sending data, red LED blinked. While the target
is receiving the data, “PROGRAM” is displayed and green
LED blinked. When cloning of data is completed, the
source displays “END”, and the source red LED turned
off, and the target automatically operates in the User
mode. The target can then be operated by the same pro-
gram as the source.
5. The other target can be continuously cloned. Carry out
the operation in step 2 to 4.
REALIGNMENT /
模式组合
7. 复制模式
通过模块化麦克风插孔连接车载对讲机，可以将编程数据
从一台传输到另一台。具体操作如下 ( 发射车载对讲机是主
机，接收车载对讲机是子机 )。 应当启用复制模式。
不能复制以下数据。
· 调谐数据
· 带密码的嵌入信息
· 机型数据
· ESN( 电子序列号 ) 数据
注意 :
可以复制以下数据。
· FleetSync 的 Fleet( 自身 )/ID( 自身 )
· NXDN 的 Unit ID( 自身 )
· MDC-1200 的 ID( 自身 )
1. 按住 [
] 键 (1 秒 ) 打开主机的电源，
LCD 上显示“CLONE
MODE”
。
2. 打开子机的电源。
3. 将复制电缆 ( 编号 :E30-3382-05) 连接到主机和子机上的
模块化麦克风插孔。
4. 按主机上的 [ ] 键。
主机的数据便被发送到子机。主机发送数据时，红色 L E D
将会闪烁。子机接收数据时，将显示“P R O G R A M”且绿色
LED 闪烁。数据复制完成后，主机显示“END”
，主机的红
色 L ED 熄灭，子机自动以用户模式运行。然后子机就可以
按与主机相同的程序操作。
5. 可以继续对另一台子机进行复制。执行步骤 2 至 4 的操作。
Fig. 2 /
图 2
Cloning cable
(E30-3382-05)
/
复制电缆
7-1. How to enter the data password
If the read authorization password is set in the optional
feature menu, you must enter the password (Source trans-
ceiver) to activate a clone mode.
You can use 0~
9
to confi gure the password. The maxi-
mum length of the password is 6 digits.
7-1. 如何输入数据密码
如果在可选功能菜单中设置了读取授权密码，则您必须输
入密码 ( 主机 ) 方可激活复制模式。
可使用 0 ～ 9 设置密码。密码最大长度为 6 位。
Summary of Contents for NEXEDGE NX-720
Page 122: ...NX 720 ...
