5
TK-2118
TK-260
:K, K2
2) Channel setting
Operation:
After entering Self-Programming Mode Press the [LOW] key.
The LCD changes to
CH 1 1
When you press the PTT switch after setting the data, you
can continue to the next Item. (Refer to page8 item 6)
…
REALIGNMENT/
模式组合
2) 信道设定
操作：
进入自台编程模式后按[LOW]键。
LCD变为
CH 1 1
当您在设置数据后按下PTT开关，您便可继续到下一项。
（请翻阅8页项目6）
选择设置项目
显示
设置内容
(例如)
信道范围1-50。
设置信道编号
当未设置信道号时，将不选
择以下项目。
(
CH 1 1 )
Selecting the setting items
Display
Setting contents
(Example)
Channel range from 1 to
50.
Setting the channel number
When a channel number is not
set, the following items will not
be selected.
(
CH 1 1 )
Blank
100.00000MHz~549.99500MHz
(VHF: 5kHz(Default) /
6.25kHz Step)
∗
1
Default (C): 150.000MHz
(C2): 140.000MHz
Setting the receive QT/DQT
When a channel number is not set,
this item will be skipped.
(
…… 2 )
(
OFF 3 ) OFF
QT(QT frequencies
table)
∗
2: 67.0Hz ~ 250.3Hz
DQT(DQT Normal/Inverse table)
∗
2: 023 ~ 754 Normal setting
DQT(DQT Normal/Inverse table)
∗
2: -023 ~ -754 Inverse setting
Setting the receive frequency
When a receive frequency is not
set ("blank" is set), the following
items will not be selected. (Item
numbers 3 to 12 are not selected.)
When "blank" is set, you will return
to "setting the channel number".
Setting the transmit frequency Same as
RX Display
(This is item
number "4".)
Same content as "Setting
the received frequency"
Setting the transmit QT/DQT
When a transmit frequency is not
set, this item will be skipped.
Same as
RX Display
(This is item
number "5".)
Same content as
"Setting the receive QT/
DQT"
(
150.000 2 )
(
q 100.0 3 )
(
d 023 3 )
(
d -023 3 )
Setting the option signalling
0: None
1: DTMF
Setting the BUSY CH Lockout
(BCL)
OFF: OFF 1: Carrier
2: QT/DQT 3: DTMF
F o r s e t t i n g n u m b e r
" 3 " ( D T M F ) , i f o f O p t i o n
Signaling is changed from
"DTMF" to "None" before the
BCL setting is entered, the
BCL setting contents will be
automatically set to "OFF"
(OFF).
S e t t i n g t h e B e a t S h i f t
function ON or /OFF
OFF: No
ON: Yes
Setting Scan DELETE / ADD
del: Scan DELETE
Add: Scan ADD
Setting Wide / Narrow
0: Narrow
1: Wide
Setting the SP Unmute
When option signaling is set
to "0" (None), this item will be
skipped.
0: Carrier or QT/DQT
1: C DTMF or QT/
DQT + DTMF
F o r s e t t i n g n u m b e r " 1 "
(C DTMF or QT/DQT +
DTMF), if Option Signaling is
changed from "DTMF" to
"None" before the SP Unmute
setting item is entered, the SP
Unmute setting contents will
be automatically set to "0"
(Carrier or QT/DQT).
Setting the transmit power
H: High power
L: Low power
(
0 6 )
(
OFF 7 )
(
OFF 8 )
(
Add 9 )
(
0 10 )
(
0 11 )
(
H 12 )
∗
1 Step change for setting the frequency
MHz step: Routed the Channel selector while pressing the
[1] key.
5kHz or 6.25kHz step: Press the [SCAN] key
设置接收频率
当未设置接收频率时(设置为
"空白")，将不选择以下项目。
(不选择项目编号3-12。)
当设置为"空白"时，您将返回
到"设置信道号"。
(
……
2 )
(
150.000 2 )
空白
100.00000MHz~549.99500MHz
(VHF: 5kHz(缺省) /6.25kHz
Step)*1
缺省
(C): 150.000MHz
(C2): 140.000MHz
设置接收 QT/DQT
当未设置信道号时，该项目
将跳过。
(
OFF 3 ) OFF
QT(QT 频率表)*2:
67.0Hz ~ 250.3Hz
DQT(DQT 正常/反向表)*2:
023 ~ 754 正常设置
DQT(DQT 正常/反向表)*2:
-023 ~ -754 反向设置
(
q 100.0 3 )
(
d 023 3 )
(
d -023 3 )
设置发射频率
与接收显示
相同(该项目
号为编号"4".)
与 "接收频率" 内容相同。
设置传送 QT/DQT
当未设置发射频率时，该项目
将跳过。
与接收显示
相同(该项目
号为编号"5".)
与 "设置接收 QT/DQT"内
容相同。
设置可选信令
0: 无
1: DTMF
设置繁忙信道锁定 (BCL)
OFF: 关
1: 载波
2: QT/DQT 3: DTMF
对于设置 "3" (DTMF)，如
果在输入BCL 设置之前可
选信令设置从" D T M F " 变
为" 无" ，则B C L 设置内容
将自动设置为 " O F F "
(关)。
设置差拍偏移功能ON或OFF
OFF: 否
ON: 是
设置扫描删除／添加扫描
del: 扫描删除
Add: 扫描添加
设置宽／窄带
0: 窄带
1: 宽带
设置SP不静音
当选择信令的选择被设置到
"0" (无)时，该项目将跳过。
0: 载波或 QT/DQT
1: 载波 + DTMF或
QT/DQT + DTMF
对于设置编号"1"(载波+
DTMF或QT/DQT+DTMF)，
如果在输入S P 不静音设置
项目之前可选信令设置从
"DTMF"变为 "无"，则SP不
静音设置内容将自动设置
为"0" (载波或QT/ DQT)。
设置发射功率
H: 高功率
L: 低功率
(
0 6 )
(
OFF 7 )
(
OFF 8 )
(
Add 9 )
(
0 10 )
(
0 11 )
(
H 12 )
∗
1 设置频率的步进
MHz档：按下[1]键的同时确定信道选择器的方向。
5kHz或6.25kHz档: 按下[SCAN]键
