62
TK-5710
(
B
)
/5710H
(
B
)
ADJUSTMENT
4. MCF
1) CH-Sig:1-1
Spectrum
Rear
ANT
TX-RX
L225
Adjust the coils
•Wide
Spectrum analyzer setting
analyzer
panel
L227
to obtain the
Center-f : 49.95MHz
L229
waveform as shown
Span
: 40kHz
Tracking
TX-RX
CN202
L231
to the right.
RBW
: 1kHz
generator
CN203
VBW
: 1kHz
TG level : -20dBm
XdB/div : 2dB
Connect each cable (W05-1000-00)
to CN202 and CN203.
•Narrow
2) Turn the [Selector] knob as
L224
“N” (Narrow) appears on
L226
the LCD.
L228
Spectrum analyzer setting
L230
Center-f : 49.95MHz
Span
: 30kHz
RBW
: 1kHz
VBW
: 1kHz
TG level : -20dBm
XdB/div : 2dB
5. 2nd local
[Panel tuning mode]
f.counter
TX-RX
SLO
TX-RX
[PF3],
Change the
50.4MHz±70Hz
adjust
1) Adj item:[W SLO]
[PF4]
adjustment value
Adjust:[***]
within the limit
Press [PF5] to store the adjust-
of the specified
ment value after adjustment.
frequency.
6. Quadrature
[Panel test mode]
SSG
TX-RX
QUAD
TX-RX
L232
Adjust the coil
1.0V±0.05V
coil adjust
1) CH-Sig:1-1
DVM
within the limit
SSG output:-53dBm(501
µ
V) AF VTVM
EXT.SP
of the specified
(DEV:OFF)
Dummy load
voltage.
7. RTC
1) CH-Sig:1-1
f.counter
CONTROL CLKC
Programming Adjust the RTC
oscillation
DVM
32KOUT
Software:
oscillation frequency
frequency
DC power
KPG-95D using the PC tuning
adjust
supply
mode. Perform the
procedures below.
1. Apply 5V DC to the
"CLKC" terminal of the
control unit (X53-412).
2. Measure the output
from the "32KOUT"
terminal of the control
unit (X53-412) using
the calibrated frequency
counter.
3. Enter the measured
frequency value to
"Crystal Oscillation
Frequency" of RTC
correction in the PC
tuning mode and then
click [OK] button.
Measurement
Adjustment
Item
Condition
Test-
Unit
Terminal
Unit
Parts
Method
Specifications/Remarks
equipment
SPAN
40.0 kHz
REF -20.0 dBm
CENTER 49.9500 MHz
RBW
1 kHz
VBW
1 kHz
SWP 200ms
SPAN 40.0 kHz
2 dB/
CAL.OFF
ATT 10 dB
−
4kHz +4kHz
−
8kHz
+8kHz
1.5dB
MAX
5.5dB
or more
TG LEVEL
-20 dBm
REF -20.0 dBm
CENTER 49.9500 MHz
RBW
1 kHz
VBW
1 kHz
SWP 150ms
SPAN 30.0 kHz
2 dB/
CAL.OFF
ATT 10 dB
−
3kHz +3kHz
−
6kHz
+6kHz
1.0dB
MAX
6.0dB
or more
Note: It is not necessary
to adjust the RTC
oscillation frequency under
normal adjustments.
The RTC oscillation frequency
must be checked and
adjusted when the 32 kHz
crystal resonator (X700) is
replaced.