13
TK-760G/
(
N
)
/762G/
(
N
)
REALIGNMENT
Cloning cable
(E30-3382-05)
Fig. 2
MBL
PSB
GND
PTT/TXD
ME
MIC
HOOK/RXD
CM
GND
REMOTE/TXD
PTT/RXD
8
1
1
8
Clone cable
E30-3411-05 (TK-760G
→
TK-260G/270G)
you press the [SCN] key, the currectly selected number is
determined, and the display shifts to the left. If you
press the [SCN] key after entering the password in this
procedure, “CLONE” is displayed if the entered pass-
word is correct. If the password is incorrect, “CLN
LOCK” is redisplayed.
4. Power on the slave TK-760G.
5. Connect the cloning cable (No. E30-3382-05) to the
modular microphone jacks on the master and slave.
6. Press the [SCN] key on the master while the master dis-
plays “CLONE”. The data of the master is sent to the
slave. While the slave is receiving the data, “–PC–” is
displayed. When cloning of data is completed, the mas-
ter displays “END”, and the slave automatically operates
in the User mode. The slave can then be operated by the
same program as the master.
7. The other slave can be continuously cloned. When the
[SCN] key on the master is pressed while the master dis-
plays “END”, the master displays “CLONE”. Carry out
the operation in step 4 to 6.
Note :
You can clone the programmed data between the trans-
ceiver frequency version must be same.
Notes :
• To start the Firmware Programmer from KPG-67D, the
FPRO path must be set up by the KPG-67D setup.
• This mode cannot be entered if the Firmware program-
ming mode is set to Disable in the Programming soft-
ware (KPG-67D).
• When programming the firmware, it is recommend to
copy the data from the floppy disk to your hard disk be-
fore you update the radio firmware.
Directly copying from the floppy disk to the radio may not
work because the access speed is too slow.
6-4. Function
1. If you press the [MON] switch while “PROG 576” is dis-
played, the checksum is displayed. If you press the
[MON] switch again (while the checksum is displayed),
“PROG 576” is redisplayed.
2. If you press the [A] switch while “PROG 576” is dis-
played, the display changes to “PROG 192” to indicate
that the write speed is low speed (19200 bps). If you
press the [A] switch again while “PROG 192” is dis-
played, the display changes to “PROG 384”, and the
write speed becomes the middle speed (38400 bps). If
you press the [A] switch again while “PROG 384” is dis-
played, the display returns to "PROG 576".
Note :
TK-762G indicate
19200 bps : The LED flashes green and red alternately.
38400 bps : The LED flashes orange.
57600 bps : The LED lights orange.
Normally, write in the high-speed mode.
7. Clone Mode (TK-760G only)
Programming data can be transferred from one radio to
another by connecting them via their modular microphone
jacks. The operation is as follows (the transmit radio is the
master and the receive radio is the slave).
1. Turn the master TK-760G power ON with the [
] key
held down. If the password is set to the TK-760G, the
TK-760G displays “CLN LOCK”. If the password is not
set, the TK-760G displays “CLONE”.
2. When “CLN LOCK” is displayed, only the [CH
/
] key
and [SCN], and [0] to [9] keys can be accepted. When
you enter the correct password, and “CLONE” is dis-
played, the TK-760G can be used as the cloning master.
The following describes how to enter the password.
3. How to enter the password with the microphone keypad;
If you press a key while “CLN LOCK” is displayed, the
number that was pressed is displayed on the TK-760G.
Each press of the key shifts the display in order to the
left. When you enter the password and press the [SCN]
key, “CLONE” is displayed if the entered password is
correct. If the password is incorrect, “CLN LOCK” is
redisplayed.
How to enter the password with the [CH
/
] key;
If the [CH
/
] key is pressed while "CLN LOCK" is dis-
played, numbers (0 to 9) are displayed flashing. When
8. Self Programming Mode (TK-760G only)
Write mode for frequency data and signalling etc. Mainly
used by the person maintaining the user equipment.
