PACKET-4
Command Name
Short
Description
Parameter
Default
DISPLAY
DISP
Causes the TNC to display the current status of all the
commands. You can also specify a class identifi er A, C, H, I,
L, M, or T to display the status of only the desired command
class. Enter a space between the command name and a
class identifi er; ex. DISPLAY H.
A (ASYNC): RS-232C port parameters
C (CHAR): Special TNC characters
H (HEALTH): Counter parameters
I (ID): ID parameters
L (LINK): TNC-to-TNC link status
M (MONITOR): Monitor parameters
T (TIMING): Timing parameters
−
−
DWAIT
DW
Specifi es the interval from no carrier detection until execution
of transmission. The unit of the parameter is 10 milliseconds.
0 ~ 250
30
ECHO
E
When ON, causes the TNC to echo received characters to
the computer.
ON/ OFF
ON
EPATH
EPATH
Specifi es digipeater callsigns to be added when the UISSID
parameter in a received packet is 10 or 14.
Call1, ... call7
−
EXTCLR
EXTC
Clears the contents of the TNC mailbox.
−
−
FILE
FI
Displays the list of all messages in the TNC mailbox.
−
−
FIRMRNR
FIR
The other station sends a notice (packet) to you if it is not
ready to receive data. When ON, receiving such a notice
causes the TNC to suspend transmission until it receives a
“ready” notice.
ON/ OFF
OFF
FLOVER
FL
Specifi es the time delay from when the TNC buffer becomes
full until the TNC buffer is cleared. The unit of the parameter
is 1 minute.
0 ~ 120
0
FLOW
F
When ON, starting key entry causes the computer to stop
displaying received packets.
ON/ OFF
ON
FRACK
FR
Specifi es the interval from one transmission until retry of
transmission. The unit of the parameter is 1 second.
0 ~ 15
3
FULLDUP
FU
When ON, allows the TNC to function in full duplex. When
OFF, allows it to use data carrier detect signals to avoid
packet collision.
ON/ OFF
OFF
GBAUD
GB
Selects 4800 or 9600 bps as the transfer rate between the
TNC and the GPS receiver.
2400/ 4800/ 9600
4800
GPSSEND
GPSS
Specifi es the content of data to be output to the GPS
receiver; this data is used to program the default settings on
the receiver. The output data is not stored in memory.
0 ~ 159 characters
−
GPSTEXT
GPST
Specifi es the type of a message to be determined by LTEXT.
0 ~ 6 characters
$PNTS
HBAUD
HB
Selects 1200 or 9600 bps as the transfer rate between
packet stations.
1200/ 9600
1200
HEALLED
HEAL
Determines whether or not normal operations of the ROM
are checked. When ON and if normal operations are
detected, “STA” and “CON” appear and blink alternately.
ON/ OFF
OFF
HID
HI
When ON, causes the TNC to send an ID packet every 9.5
minutes after digipeating.
ON/ OFF
ON
ID
I
Causes the TNC to send an ID packet.
−
−
KILL
KI
Deletes specifi c messages in the TNC mailbox.
−
−
KISS
KISS
When ON, entering a RESTART command causes the TNC
to enter (or exit) KISS mode.
ON/ OFF
OFF
LCSTREAM
LCS
When ON, changes a small letter (a through z) entered as a
stream designator, to a capital letter (A through Z). A stream
designator must be entered immediately after STREAMSW.
ON/ OFF
ON
LIST
LI
Displays the list of messages, in the TNC mailbox, other than
those addressed to other stations.
−
−
