background image

MODEL

O P E R AT O R ’ S   M A N U A L

IMPORTANT NOTES:

1)

This manual is valid for the following Model and associated serial numbers:

MODEL

SERIAL NO.

REV. NO.

2)

A  Change  Page  may  be  included  at  the  end  of  the  manual.  All  applicable  changes  and
revision  number  changes  are  documented  with  reference  to  the  equipment  serial  num-
bers. Before using this Instruction Manual, check your equipment serial number to identify
your model. If in doubt, contact your nearest Kepco Representative, or the Kepco Docu-
mentation Office in New York, (718) 461-7000, requesting the correct revision for your par-
ticular model and serial number.

3)

The contents of this manual are protected by copyright. Reproduction of any part can be
made only with the specific written permission of Kepco, Inc. 

 

Data subject to change without notice.

KEPCO

®

THE POWER SUPPLIER™

KEPCO, INC.

z

  131-38 SANFORD AVENUE  

z

  FLUSHING, NY. 11355 U.S.A.  

z

  TEL (718) 461-7000  

z

  FAX (718) 767-1102

email: hq@kepcopower.com  

z

  World Wide Web: http://www.kepcopower.com

KEPCO INC.

An ISO 9001 Company.

©201

9

, KEPCO, INC.

P/N 228-1730

-R

2

JQE  1/4 RACK

POWER SUPPLY

INCLUDES MODEL SUFFIX 

M, D

M

100W

JQE 6-10, JQE 15-6,
JQE 25-4, JQE 36-3,

JQE 55-2, JQE 75-1.5, 

JQE 100-1

Summary of Contents for JQE 100-1





































Reviews: