background image

MST SERIES 10/26/07

3

Model Number)______________________________________

Serial Number_______________________________________

Date Purchased:_____________________________________

Date Received:______________________________________

 # 

Send complete Catalog

 # 

Have Sales Engineer Call

Contact via: 

 # 

E-Mail  

   # 

Telephone  

    # 

Fax    

 # 

S-mail    

PRODUCT PURCHASED:

PURCHASE INFORMATION:

REQUEST ADDITIONAL INFORMATION

Registered by:________________________________________

Company Name:______________________________________

Street: ______________________________________________

City:________________________________________________

State:_______________________________________________

Country:_____________________________________________

Zip:_________________________________________________

E-mail: ______________________________________________

FAX:____________________________________________

Phone: _________________________________________

REGISTER TO:

This is to certify that we, KEPCO, INC., (hereinafter called “Company”), Flushing, NY

11355 USA, warrants for a period of FIVE YEARS, this instrument known as:

MODEL:

__________________________________________

SERIAL NO. _________________________________________

The Company’s products are warranted for a period of five years from date of delivery to

be free from defects in materials and workmanship and to conform to the specifications

furnished or approved by the Company. Liability under this warranty shall be limited to

the repair or replacement of any defective product at Company’s option. 

If any defect within this warranty appears within the warranty period, the Purchaser shall

promptly notify the Company in writing. No material will be accepted for repair or

replacement without written authorization of the Company.

Upon such authorization, and in accordance with instructions of the Company, parts or

materials for which replacement is requested shall be returned to the Company for

examination, with shipping charges prepaid by the Purchaser. Final determination as to

whether a product is actually defective rests with the Company. 

This warranty does not extend to any product which has been subjected to misuse,

neglect, accident, improper installation, or use in violation of instructions furnished by

the Company. The warranty does not extend to, or apply to, any unit which has been

repaired or altered outside of the Company’s factory by persons not expressly approved

by the Company. 

THE WARRANTY HEREIN CONTAINED IS IN LIEU OF AND EXCLUDES ALL OTHER

WARRANTIES, EXPRESS, IMPLIED OR STATUTORY, INCLUDING WITHOUT

LIMITATION THE WARRANTY OF MERCHANTABILITY.

Kepco 5 Year Warranty

KEPCO, INC.  

"

  131-38 SANFORD AVENUE, FLUSHING, 

NY 11355 USA  

"

  Tel. 718-461-7000  

"

  Fax. 718-767-1102

E-mail: hq@kepcopower.com  

"

  URL: http://www.kepcopower.com

THIS KEPCO PRODUCT IS WARRANTED FOR FIVE YEARS!

WHAT INFLUENCED YOUR CHOICE OF THIS POWER SUPPLY?

 # 

Previous Experience (which Kepco Models do you have?)

______________________________________________________

______________________________________________________

______________________________________________________

 # 

Magazines (which ones?)_____________________________

______________________________________________________

 # 

Trade Shows (which ones?)___________________________

 # 

Directory?__________________________________________

 # 

Kepco Catalog or Brochure?__________________________

 # 

Sales Representative?

 # 

Web Site

 # 

Other (please explain):_____________________________

 
What products would you like to see Kepco make?

____________________________________________________

____________________________________________________

____________________________________________________

You must register your product to comply with the terms of the warranty. Either fill out the form
below and mail or fax to Kepco, or for rapid on-line registration go to:

 

http://www.kepcopower.com/warranty.htm

 

CUT HERE

Summary of Contents for KLP 10-150-3

















Reviews: