SELENA
Multifunctional LED Clock
USER MANUAL V32D
KERA TECHNOLOGIES INC. 2013
www.ledclocks.com
14
MONTH:YEAR display, followed by EXTERNAL TEMPERATURE display and all over again: HOURS:MINUTES display
followed by ... etc...etc...
NOTE,
that the Real Time Clock mode (Fn 3), when alternating with other displays, always persists on the display the longest
(appx. 10 sec) while other displays will each remain on for shorter periods (appx 5 sec). This persistence split may be altered
by enabling the functions
Fn 40
and / or
Fn 41
.
If only one display mode is enabled, it will remain on the display all the time.
All three Time display Formats are available in all SELENA clocks.
The Function Fn 8 can be used to select between the
12 and 24 hour format
.
To select the
Military Time format
, enable the function Fn 45.
To select the display of
AM or PM
text indicator in the 6-digit clock, or in the Text display,
enable the functions Fn 8 and Fn 85.
HALTING the ALTERNATING DISPLAY in the Digital Time section
The user may
(ON DEMAND) HALT
the alternating display by pressing the
HOLD
key at any time. The screen currently on
the display will remain active until either a programming mode is initiated or the
SCAN
key is pressed.
Similarly, whenever the Timer/Counter START, STOP or RESET is performed externally or via the remote, the display will
switch to the timer/counter mode. Press the
SCAN
key to return to other display screens.
To scroll quickly through the enabled screens, press the
SCAN
key repeatedly.
NOTE:
when the function
Fn 62
is enabled,
ALL COMMUNICATION
with the clock via the remote control is
DISABLED
.
To regain the remote control access disconnect the power momentarily, then restore it and disable
Fn 62
within 33 seconds.
Also see the function
Fn 63
to disable the remote communication except the timer functions and the brightness control .
DATE / TEXT and ZONE Text display
( Optional Feature )
The TEXT option may be activated by enabling the function Fn 85.
In clocks with the optional Alpha Numeric text display installed, several modes for displaying of the current date and other text
modes may be selected by enabling the functions as per the table below:
Fn64
Fn65
Fn66
Mode “0”
OFF
OFF
OFF
*
no date display
Mode “1”
ON
OFF
OFF
FRI-OCT-12
Mode “2”
OFF
ON
OFF
OCT-12-FRI
Mode “3”
ON
ON
OFF
12-OCT-FRI
Mode “4”
OFF
OFF
ON
FRI-12-OCT
Mode “5”
ON
OFF
ON
12-OCT-2007
Mode “6”
OFF
ON
ON
OCT-12-2007
Mode “7”
ON
ON
ON
2007-12-OCT
*
NOTE
: If the Functions Fn 64, 65, 66 are set to 000, the
Date
will
NOT
be displayed. However other text modes may still be
activated and will display in an
alternating manner
if more than one is enabled.
Mode “8”
Fn 72
HH-MM-SS-hh ( timer or counter ) ( also see Fn 35,38,39, )
Mode “9”
Fn 73
Tmr MM-SS ( timer ) ( also see Fn 35,38,39, )
Mode “10”
Fn 74
TIMER HH-MM ( timer or counter ) ( also see Fn 35,38,39, )
Mode “11”
Fn 75
OUT 25 C ( or 77 F ) ( also see Fn 0 , Fn 1 and Fn 15 )
Mode “12”
Fn 76
IN 25 C ( or 77 F ) ( also see Fn 0, Fn 1 and Fn 15 )
Mode “13”
Fn 77
TEMP 25 C ( or 77 F ) ( also see Fn 0, Fn 1 and Fn 15, 27 )
Mode “14”
Fn 78
DAY 245 ( Julian day of the year )
Mode “15”
Fn 79
HH-MM-SS AM/PM ( real time clock ) ( also see Fn 8, 45, 84 )
Mode “16”
Fn 80
TIME ZONE / Customer TEXT DISPLAY ( also see Fn 86 )
NOTE
1
: In order to make any
Text display alternate with other Text
, enable more than one text display mode.
NOTE
2
: The
alternating text display
is
“halted”
automatically if the
FUN
key is pressed or whenever any of the clock
programming modes is initiated. To resume the alternating text display after programming, press the
TALK
key.
