background image

23 

 

OBE-1-BA-e-1611 

Trouble shooting 

 

Problem 

Possible causes 

The bulb does not light 

The mains plug is not correctly plugged in 

There is no power at the socket 

Defective bulb 

Defective fuse 

The bulb blows immediately 

The specified bulb or fuse has not been used 

The field of view is dark 

The aperture diaphragm and/or field 
diaphragm are not opened wide enough 
The selector switch for the beam path is set 
to “Camera” 

The condenser is not correctly centred 

You cannot adjust the brightness 

The brightness control has been set 
incorrectly 
The condenser has not been correctly 
centred 

The condenser is too low 

The field of view is dark or is not 
correctly  
illuminated 

The objective is not positioned correctly on 
the beam path 
The selector switch for the beam path is 
between two settings 

The nosepiece is not correctly fitted 

The condenser is not correctly fitted 

An objective is being used which doesn’t 
match the lighting area of the condenser 
The condenser has not been correctly 
centred 

The field diaphragm is closed too tightly 

The bulb is not correctly fitted 

The field of view of one eye does not 
match that of the other eye 

The interpupillary distance is not correctly 
adjusted 
Dioptre setting has not been carried out 
correctly 
Different eyepieces are used for the 
righthand and lefthand side 

The eyes are not used to using a microscope 

 

 

Summary of Contents for OBE 101



























Reviews: