background image

OBL-14-15-BA-e-1610 

 

18 

5.8  Using oil immersion objectives 

 
The 100x objectives of the OBL-14 and OBL-15 series are objectives  which  can be 
used with oil immersion (they are always marked with the word “OIL”). Using these 
generates a particularly high resolution for microscopic images. 
 
 
To use oil immersion correctly, please follow these steps. 
 
1.  Put  a drop of oil on the cover glass  (with standard thickness of 0.17 mm) of the 

object slide. 
 

2.  Lower the specimen stage and position the 100x objective in the beam path. 

 

3.  Bring the specimen stage or object slide to the objective very slowly until there is 

slight contact. 

 

4.  Observe the object. 
 
 
The  object  slide  and  objective  must  not  be  pressed  against  each  other.  The  oil 
constitutes the contact layer. 

 

If the contact is made too jerky, there is a chance that existing air bubbles in the oil 
cannot escape. This would have a negative impact on image clarity. 
 
 
 
After use or before changing the slide, any components which have been in contact 
with the oil must be cleaned thoroughly. 

See also 1.4 Maintenance and cleaning.

 

 
 
 
 

 

Summary of Contents for OBL 145





























Reviews: