background image

OBL-14-15-BA-e-1610 

 

22 

Changing the fuse 

 

The  fuse  housing  is  on  the  rear  of  the  microscope  below  the  mains  power  supply 
socket.  With  the  device  switched  off  and  unplugged,  you  can  pull  out  the  housing. 
When doing this, it is helpful to use a screwdriver or similar tool. The defective fuse 
can be removed from its housing and be replaced with a new one. 
After that, you just need to insert the fuse housing back into the insertion point below 
the mains power supply socket. 
 
 

Using optional accessories 

 

8.1  Camera connection 

OBL 155 

 
Due  to  the  trinocular  tube,  which  is  a  standard  fitting  for  the  model  OBL  155,  it  is 
possible  to  connect  microscope  cameras  to  the  device,  in  order  to  digitally  record 
images or sequences of images of an object being observed. 
 
After the plastic cover has been removed from the camera adapter connector on the 
top of the microscope head, then a suitable adapter must be fitted. 
In  general  there  are  two  C-mount  adapters  available  for  this  (1x  and  0.47x 
magnification, 

see Chapter 3 Features

). After fitting one of  these adapters it can be 

fixed with the fixing screw. A camera which has a C-mount thread is then screwed on 
top of the adapter. 
 
We  recommend  that  you  first  adjust  the  field  of  view  using  the  eyepieces  on  the 
device  for  the  existing  requirements,  and  then  carry  out  the  observation  using  the 
microscope camera (i.e. using the PC screen which is connected). 
The  tube  has  a  light  distribution  that  guarantees  the  providing  of  light  for  the 
eyepieces  and  the  camera  connection  at  the  same  time.  This  means  that  it  is 
possible to simultaneously observe by the eyepieces and PC screen. 
 
For  C-mount  adapters,  which  have  their  own  integrated  magnification,  the  image 
which  is  shown  on  the  camera  connected  to  the  device  can  often  have  a  different 
level of focus compared with the image on the eyepiece. 
In  order  to  be  able  to  bring  both  images  into  focus,  the  focus  can  be  adjusted  by 
those adapters. 

 
 

 
 

 

Summary of Contents for OBL 145





























Reviews: