background image

 

YBI-01A-BA-e-1620 

 

Mains connection 

Select a country-specific power plug and insert it in the 
power unit. 
Power is supplied via the external mains adapter. The 
stated voltage value must be the same as the local 
voltage.  
Only use original KERN mains adapters. Using other 
makes requires consent by KERN.  
Turn off the ionizer (master switch “OFF“) before 
connecting it to the mains adapter. 

 
  

Commissioning 

Turning on the ionizer 

 

Set master switch to “ON“.  
The green LED starts glowing. 

During normal operation the green LED will be glowing, in 
case of a breakdown the red LED.  

If the red LED is glowing, turn off the ionizer at the master 
switch and turn it on again.  If the red LED continues to 
glow, disconnect the device from the mains and contact 
the manufacturer. 
 
After use turn off with master switch "OFF". 

Turning on the fan 

Ionisation results are better when the fan is turned on and 
the period required for discharging the sample will be 
shortened.  

Information: 
Turn off fan for powdery, easily whirled up samples.  

 

Set switch of fan to “ON”.  
The yellow LED starts glowing. 

Ensure sufficient ventilation even when the fan is turned 
on. 
 
 
 

Summary of Contents for YBI-01A












Reviews: