background image

IMPORTANT SAFETY INSTRUCTIONS

Warning 

When using electric tools basic safety precautions should always be followed to reduce the risk of fi re, electric shock, and personal injury, including the 
following:
 

Read all instructions. 
Save these instructions. 

For KL-200 and all double insulated tools: 

When servicing, use only identical replacement parts.
 

SPECIFIC SAFETY RULES 

Keep Work Area Clean 

Cluttered areas and benches invite accidents. Keep work area well lit. 

Avoid Dangerous Environment

 Don’t expose power tools to rain or snow. Don’t use power tools in damp or wet locations. 

The symbol on the Caution Label is mean to convey this message. Ne pas exposer a la pluie et ne pas utiliser dans les emplacements humides. 

Defi nitions of Symbols

N

- No load speed

  

/min - per minute
Double insulated motor

Gaurd Against Electric Shock

 

Prevent body contact with grounded surfaces, for example: pipes, radiators, ranges, refrigerator enclosures. 

Keep Children Away

 

Do not let visitors contact tool or extension cord. All visitors should be kept away from work area. 

Store Idle Tools

 

When not in use, tools should be stored in dry, high or locked-up place out of reach of children. 

Don’t Force Tool

It will do the job better and safer at the rate for which it was designed. 

Use Right Tool

Don’t force a small tool to do the job of a heavy duty tool. Don’t use tool for on purpose not intended, for example-don’t use a circular saw for cutting tree 
limbs or logs.

Dress Properly

Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves and footwear are recommended when working out doors. 
Wear protective hair covering to contain long hair.

Use Safety Glasses

Use safety equipment. Always wear eye protecion.

Don’t Abuse Cord

Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from heat, oil, and sharp edges. Replace damaged cords immediately.

Secure Work

 

Use clamps or vise to hold work. It’s safer than using your hand and it frees both hands to operate tool.
 

Don’t Overreach

.

Keep proper footing and balance at all times.

Summary of Contents for KL-200







Reviews: