Kettler 07670-600, Instruction Manual

5

Handling the equipment

■

Before using the equipment for exercise, check carefully to en-
sure that it has been correctly assembled.

■

It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust. Please ensure that no part
of the machine comes in contact with liquids (drinks, perspi-
ration etc.). This may cause corrosion.

■

The machine is designed for use by adults and children
should not be allowed to play with it. Children at play beha-
ve unpredictably and dangerous situations may occur for
which the manufacturer cannot be held liable. If, in spite of
this, children are allowed to use the equipment, ensure that
they are instructed in its proper use and supervised accor-
dingly.

■

The equipment is independent of revolutions per minute.

■

A slight production of noise at the bearing of the centrifugal
mass is due to the construction and has no negative effect
upon operation. Possibly occurring noise during reverse pe-
dalling result from engineering and are absolutely safe.

■

The training device has a electromagnetic brake system.

■

To operate correctly, the pulse function requires a minimum

voltage of 2,7 volts (only for computers working with batte-
ries).

■

Before beginning your first training session, familiarize yours-
elf thoroughly with all the functions and settings of the unit.

Care and Maintenance

■

Damaged components may endanger your safety or reduce
the lifetime of the equipment. For this reason, worn or dama-
ged parts should be replaced immediately and the equipment
taken out of use until this has been done. Use only original
KETTLER spare parts.

■

To ensure that the safety level is kept to the highest possible
standard, determined by its construction, this product should
be serviced regulary (once a year) by specialist retailers.

■

Use for your regular cleaning, maintenance and care our ap-
pliance maintenance set (Article no. 07921-000) specifically
licensed for KETTLER Sports apparatus and available from the
Sport specialized trade.

■

Please ensure that liquids or perspiration never enter the ma-
chine or the electronics.

List of spare parts page 41-46

When ordering spare parts, always state the full article number,
spare-partnumber, the quantity required and the S/N of the pro-
duct (see handling).

Example order:

Art. no. 07670-700 / spare-part no. 94318447

/ 2 pieces / S/N .................... Please keep original packaging
of this article, so that it may be used for transport at a later date,
if necessary.
Goods may only be returned after prior arrangement and in (in-
ternal) packaging, which is safe for transportation, in the original
box if possible. It is important to provide a detailed defect de-
scription / damage report!

Important:

spare part prices do not include fastening material if

fastening material (bolts, nuts, washers etc.) is required, this
should be clearly stated on the order by adding the words „with
fastening material“.

Waste Disposal

KETTLER products are recyclable. At the end of its
useful life please dispose of this article correctly and
safely (local refuse sites).

KETTLER GB Ltd.

Kettler House, Merse Road

+44 1527 591901

North Moons Moat 

+44 1527 62423

Redditch, Worcestershire B98 9HL

www.kettler.co.uk

Mail:

sales@kettler.co.uk

KETTLER International Inc.

1355 London Bridge Road

+1 888 253 8853

Virginia Beach, VA 23453

+1 888 222 9333

www.kettlerusa.com

USA

GB

■

The fastening material required for each assembly step is sho-
wn in the diagram inset. Use the fastening material exactly as
instructed. 

■

Bolt all the parts together loosely at first, and check that they
have been assembled correctly. Tighten the locknuts by hand
until resistance is felt, then use spanner to finally tighten nuts
completely against resistance (locking device). Then check that

all screw connections have been tightened firmly. Attention:
once locknuts have been unscrewed they no longer function
correctly (the locking device is destroyed), and must be repla-
ced.

■

For technical reasons, we reserve the right to carry out preli-
minary assembly work (e.g. addition of tubing plugs).

GB