Kettler KETTRIKE JUNIOR 08152-599, Assembly Instructions Manual

I

When children are at play, situations may arise which cannot be predicted by the manufacturer and

for which we cannot be held responsible.

I

Before use, always check all screws and plug-in connections as well as respective safety devices fit correctly.

I

Never use corrosive or abrasive substances to clean the toy. Never use substances which may cause pol-

lution of the environment.

I

Lubricate the bearing sleeves of the wheels and the handlebars with a few drops of oil every two or three months.

I

For models with push bars: Always ensure that the push bar fits correctly in the adaptor, and locks. Do not

hang any weights on the bar! The vehicle may tip over, and your child may be hurt. The push bar is inten-

ded for adult use only, do not pass responsibility for children on to other children. For free play time take the

push bar off for safety reasons.

Assembly of the toy vehicle

I

The toy vehicle must be assembled carefully by an adult person. Study the assembly instructions care-

fully before beginning work. Assemble the vehicle in the exact sequence shown by the letters in the

diagrams. This is essential for the safe function and use of the scooter

I

Please note that there is 

always

a danger of injury when working with tools or doing manual work.

Therefore please be careful when assembling this machine.

I

Ensure that your working area is free of possible sources of danger, for example don’t leave any tools

lying around. Always dispose packaging material in such a way that it may not cause any danger.

There is always a 

risk of suffocation

if children play with plastic bags!

I

Bolt all the parts together loosely at first, and check that they have been assembled correctly. Tighten

the locknuts by hand until resistance is felt, 

then use spanner to finally tighten nuts com-

pletely against resistance (locking device)

. Then check that all screw connections have been

tightened firmly. 

Attention:

once locknuts have been unscrewed they no longer function correctly (the

locking device is destroyed

), and must be replaced.

I

The grips can be pushed onto the handlebars more easily if they are first soaked in warm water.

I

Please keep original packaging of this article, so that it may be used for transport at a later date, if necessary.

I

For technical reasons, we reserve the right to carry out preliminary assembly work (e.g. addition of

tubing plugs).

I

When ordering spare parts, always state the full item number, spare-part number, the quantity required and

the serial number of the product.

Example order:

item # 08152-599 / spare-part # 

10111023

/ 1 piece /  s/n ...

Important:

spare part prices do not include fastening material; if fastening material (bolts, nuts, washers etc.)

is required, this should be clearly stated on the order by adding the words 

„with fastening material“.

KETTLER limited warranty

THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THE MANU-
FACTURER ON KETTLER PRODUCTS, EXCEPT THE MANUFACTURER’S LIMITED WARRANTY AGAINST DEFECTS
IN MATERIAL SET OUT BELOW:

This KETTLER Limited Warranty applies to products sold through the KETTLER Authorized Dealer

Network to the original retail purchaser and authenticated by proof of purchase from a retailer loca-

ted in the United States.  Any shipments made under this warranty will be shipped to the United

States only.  Any shipment outside of the United States will be at the sole cost of the customer.  This

KETTLER Limited Warranty is a manufacturer’s warranty and is not changed or modified by additio-

nal warranties extended by individual retailers at the point of sale.  Manufacturer warrants this pro-

duct to be free from defects in material at the time of the product’s tender of delivery for a period of

3 years for residential use and 1 year for non-residential use.  This Limited Warranty is not transfe-

rable and does not cover normal wear and tear (including, but not limited to, damage and wear to

tires, power shocks, drive belts and other non-durable parts).  The liability of the manufacturer under

Warranty

3