2 - INTRODUCTION TO THE PRODUCT
4 - PROGRAMMING
DIGITAL SELECTOR FOR AUTOMATIC DOORS LEVANTE
The SEL5 Digital Selector is a device for reading CARDL cards that can be combined with automatic
doors. Communication with the CTLEV control unit takes place via the Bus interface.
Since it is possible to install 2 SEL5 readers on the same BUS network, it is necessary to set the
reader number using the DIP1 dip switch.
4.1 READER NUMBER SETTING
READER NUMBER
DIP1
1
2
NOTES: Attention: the dip switches must be set with the readers switched off; the learning takes place
when switching on. Two or more readers with the same address cannot coexist.
For proper operation, the BUS network requires a twisted cable with an impedance of 120 ohms. A
single cable cannot be longer than 50m; if the latter is laid together with 230 Vac power cables, its
maximum length will be significantly reduced to overcome the disturbances induced on it. The network
must propagate from point to point and never as a star. In any case, it is essential to respect polarities,
to overcome problems of erroneous reference to mass and Vdc, and reliability in data communication.
4.2 WIRING
1 - SAFETY WARNINGS
EN
3 - PRELIMINARY CHECKS
WARNING - for the safety of people, it is important to observe these instructions and keep
them for future use.
Read the instructions carefully before installation. The design and manufacture of the devices which
make up the product and the information contained in this manual comply with the current safety
standards in force. However, incorrect installation and programming can cause damage to property
and injury to persons who carry out the work and those who use the system. It is, therefore, important
to carefully follow all the instructions given in this manual during installation.
WARNING - before installing the product, verify and check the following points:
•
Check that the surface on which the device will be fixed is solid and does not vibrate
•
Use suitable electrical connections for the current required
•
Check that the power supply complies with the values of the technical specifications
•
Disconnect the power supply before installing
•
Make sure there is a circuit breaker in the power supply system with a distance between the contacts
that allows for total disconnection under the conditions laid down by overvoltage category III
DESCRIPTION
EXAMPLE
BEEP
During the power up phase the blue LED will light up
and at the same time a short beep will be heard.
BLUE
<1s
If there are no cards in memory, you will hear two long
beeps and the blue LED will start flashing slowly.
1s +
1s
>1s + >1s
DESCRIPTION
EXAMPLE
BEEP
Pass THE MASTER card on the receiver as many times
as the number of the service you want to match.
1 = START
2 = EXTERNAL RADAR
3 = INTERNAL RADAR
MASTER
A short beep will be heard periodically if you have
chosen to match service number 1, two short beeps for
service number 2 etc.
<1s + <1s
Pass the USER card on the receiver
USER
A short beep will indicate that the card has been learned
correctly.
<1s
DESCRIPTION
EXAMPLE
BEEP
Pass the MASTER card on the receiver 4 times
MASTER
You will hear a beep periodically indicating that you can
DELETE a USER card
<1s + <1s
Pass the USER card to be deleted on the receiver
USER
A short beep will indicate that the card has been deleted
successfully.
<1s
NOTES: If there is at least one card in memory there will be no further beep signals and the blue LED
will start flashing briefly.
NOTES: The learning process will continue for a further 15 seconds after which it will automatically cease.
NOTES: Once a card has been deleted, the procedure will automatically end. To finish the procedure
manually, simply pass the MASTER card again.
If the SEL5 reader does not contain any cards in memory, you will first need to learn a MASTER card.
To learn the first MASTER card, simply pass it on the SEL5 reader; you will hear a short beep sign that
the card has been learned and the blue LED will begin to flash briefly.
4.4 LEARNING THE FIRST MASTER CARD
4.5 LEARNING AND CHANGING SERVICE IN USER CARDS
4.6 DELETING USER CARDS
At least one MASTER card must be in memory to learn a USER card. Simply follow these steps to
learn a USER tab.
To delete A USER card, simply follow these steps.
4.3 FIRST START-UP
Summary of Contents for SEL5
Page 15: ......
