Key Digital KD-HDMS10X6, Setup Manual

Page 15

System Control Setup Commands:

Copy EDID 

information to Rx 

card slot, from 

Tx card slot yy 

via HDMI/CAT5/

or use Default 

EDID library

SP C EDID 

xx H/C/D yy

xx = Input card 

number (01-08), 
H = HDMI,  

C = CAT5,  

D = Default EDID 

library
yy = (01-08),  

01-08 Output card 

number when ‘H’ 

/ ‘C’ is selected 

–OR- 

(01-08) Default 

EDID library when 

‘D’ is selected.

To copy the EDID information from an Output card 

(display), to an Input card (source).

Example:

 To copy the EDID information from HDMI 

Output 2, to HDMI Input 4, issue the command; 

‘SPCEDID04H02’

Example:

 To copy the EDID information from CAT5 

Output 2, to HDMI Input 4, issue the command; 

‘SPCEDID04C02’  

Example:

 To load ‘DEFAULT2’ EDID library for Input 

card 3, issue the command; ‘SPCEDID03D02’ 
Below are the Default EDID library choices when 

selecting ‘D’ as a variable:
01 = DEFAULT1 (1080i 2CH PCM) 
02 = DEFAULT2 (1080p 2CH PCM)     
03 = DEFAULT3 (1080i PCM, DTS/DOLBY.  

not including HD audio)      
04 = DEFAULT4 (1080p PCM, DTS/DOLBY.  

not including HD audio)  
05 = DEFAULT5 (1080i every audio  

including HD audio)
06 = DEFAULT6 (1080p every audio  

including HD audio) 
07 = DEFAULT7 (3D 1080p 2CH PCM)              
08 = DEFAULT8 (3D 1080p every audio  

including HD audio) 

Front Panel 

Buttons 

SPCFBE/D

E = Enabled /  

D = Disabled

To Enable or Disable the front panel buttons.

Example:

 To Disable the front panel buttons, issue 

the command; ’SPCFBD’

Adjust EQ for 

CAT5 length  

per Input

SPCCAT5IC 

xxyy

xx = Input number
yy = EQ Value 

0-40 (default is 20)

To adjust CAT5 Input EQ for fine tuning Video signal 

if necessary

Example:

 To adjust CAT5 Input 6 EQ to value 30, 

issue the command: ‘SPCCAT5IC0630’

Configure CAT5 

Output to either 

DDC or PCM 

Audio

SPCCAT5OC 

hhhh

‘hhhh’ = hex value 

for Input or Output 

numbers selected.

To set CAT5 Output to either DDC (Data Display 

Channel) or PCM Audio.
Default or unselected will be DDC, selected Inputs/

Outputs will be PCM Audio.
Binary value 0 = DDC, 1 = PCM Audio

Example:

 To set the CAT5 output of outputs 1 and 

6 to PCM, issue the command; ‘SPCCAT5OC2100’, 

all other outputs will remain DDC

Reset to Factory 

Defaults

SPCDFxx

xx = 01-08 and 

represents the 

default EDID 

choice desired 

after reset. (See 

menu 7-EDID 

Set Up options 

for default EDID 

choices)

To reset factory default settings by type.

Example:

 To reset to 1080p HD Audio EDID, issue 

the command; ‘SPCDF06’

Please see our website product page for a complete list of all RS-232 commands:  
www.keydigital.com