background image

2

8

Keysight PXIe Chassis Family Startup Guide

1.

2.

3.

The two cases described above where Connection Expert does not display the 
chassis or a module in the chassis can occur with Connection Expert. If the 

New 

 Wizard is displayed, follow the steps in the Using Connection 

Hardware Found

Expert to connect to the chassis section in the 

Keysight PXIe Chassis Family 

 to associate a driver with the device. If Connection Expert, does not 

Startup Guide
display a particular device, click the 

 button to see if Windows has now 

Rescan

assigned a driver to the device, which will allow Connection Expert to display the 
device.

In general, if it ever appears that your chassis configuration as displayed by 
Connection Expert differs from your actual configuration, click the 

 button. 

Rescan

This should align the displayed configuration to the actual configuration.

Even with the latest version of IO Libraries, it is always advisable to boot the PC 
a second time to ensure that the PC properly enumerates all of the modules 
within the chassis.

Using Connection Expert to connect to the chassis

Use Connection Expert to confirm that the host controller can connect to the 
chassis.

  

Start Connection Expert on the host controller.

 

Click the 

PXI/AXIe Chassis

 tab.

  

Click the 

Chassis Content

 tab.

The list of connected chassis appears on the right hand pane as shown in the 
following image. The chassis indicator is Chassis 2. When you click on Chassis 2, 
the contents of each slot in the PXIe chassis are displayed in the right pane.

Summary of Contents for M9019A PXIe





































Reviews: