background image

 

 

30/44 

Scienlab Regenerative AC Emulator 

 Keysight SL1200A Series 

 Operating Instructions 

3           Connection and Assembly 

 

 

HSI Uplink / HIS Downlink 

 

On the top of the Output Box on the rear side 

 

Ethernet connection ports (RJ45) 

 

For parallel connection director/follower systems 
(see 

Figure 5

) 

 
The following Figure 5 shows an example for a parallel connection via Re-
mote Power Terminal (RPT). 

 

Figure 5: Schematic for parallel connection (connection via remote power termi-
nal (RPT) as an example) 

For more information please refer to the help file of the PC software 
SL1200A Regenerative AC Emulator Soft Front Panel on 

keysight.com

. 

Connecting signal and control lines 

Communication interfaces 

Additional signal and control connections can be found the roof of the 
output box, on the rear side of the system. Here are communication inter-
faces (RJ45 sockets) for the connection of an operating computer (Ether-
net connection port) or interfaces (BNC sockets) for trigger signals. 

 

Ethernet Interface 

 

On the top of the Output Box on the rear side 

 

Communication interface to the operating PC 

Trigger In / Out, BNC sockets 

 

On the top of the Output Box on the rear side 

 

Freely usable interface (e. g. for external oscilloscope) 

 

Input: reaction to trigger signals 

 

Output: sending a trigger signal on specified events 

 

Summary of Contents for SL1200A Series













































Reviews: