96
KeysightE1406A Command Module Service Guide
Error Messages
Introduction
41
INVALID UDEF INTR TABLE
The valid flag in the user-defined interrupt line allocation table is
not true (1)
.
VXI:CONF:ITAB < address> has been set but is
pointing to an invalid table
.
Either the table is corrupt or has not
been downloaded.
42
INVALID UDEF INTR TABLE DATA
The interrupt line allocation table has invalid data. The number of
records is less than 1 or greater than 7
,
the interrupt line
specified is less than 1 or greater than 7
,
or the number of
interrupters or handler ID is less than 1 or greater than 254.
43
INVALID UDEF MEM TABLE
The valid flag in the user-defined A24/A32 address allocation
table is not true (1)
.
VXI:CONF:MTAB < address> has been set
but is pointing to an invalid table
.
Either the table is corrupt or
has not been downloaded.
44
INVALID UDEF MEM TABLE DATA
An invalid logical address was specified in the A24/A32 address
allocation table
.
The logical address range is
0
to 255 or
-
1.
45
WARNING
NVRAM CONTENTS LOST
System non
-
volatile memory was cleared during a re
-
boot.
DIAG:BOOT:COLD was executed or the memory had an invalid
checksum
.
Backup battery may be disconnected or discharged
.
46
MESG BASED OPEN ACCESS FAILED
IBASIC or GPIB access to a message
-
based device failed
because of a device failure. The resource manager tries to open
a path between the GPIB port and/or IBASIC and
message
-
based devices (I and I4) using word serial commands.
The device either failed to respond
,
or the device violates the VXI
word serial protocol specification
.
47
GRANTED DEVICE NOT FOUND
The command module
,
when not the resource manager
,
was
granted a device that does not exist.
48
WARNING
DRAM CONTENTS LOST
Downloaded driver non
-
volatile memory was cleared during a
re
-
boot
.
DIAG:BOOT:COLD was executed or the memory had
an invalid checksum. Backup battery may be disconnected or
discharged
.
49
VME SYSTEM CONTROLLER
DISABLED
The System Controller switch on the command module is set to the
’Disable’ position
.
5
0
EXTENDER NOT SLOT
0
DEVICE
A VXI-MXI mainframe extender module is not in slot
0
of its
(remote)
mainframe.
51
INVALID EXTENDER LADD WINDOW
Modules do not fit in the logical address window set by the
user-defined extender table
.
Not all of the devices found “below”
an
extender will fit into the largest available window for that
extender. Either reset the logical addresses or use the extender
table to override the default algorithm
.
Table 5-3
Command Module Resource Manager Configuration Errors (continued)
Summary of Contents for VXI bus 75000 C Series
